D
Command formats (Continued)
•
Bandscope edge frequency settings
Command: 1A 05 0202 ~ 1A 05 0210
1 kHz: 0
~
9
100 Hz: 0 (fixed)
100 kHz: 0
~
9
10 kHz: 0
~
9
10 MHz: 0
~
9
1 MHz: 0
~
9
1 kHz: 0
~
9
100 Hz: 0 (fixed)
100 kHz: 0
~
9
10 kHz: 0
~
9
10 MHz: 0
~
9
1 MHz: 0
~
9
q
X 0 X X X X X 0 X X X X
w
e
r
t
y
Lower edge
Higher edge
•
Manually entered position data
Command: 1A 05 0257, 0283, 0297, 23 02
X X
X X
y
~
!1
∙∙∙∙∙∙∙
X X
X X
!2
~
!5
∙∙∙∙∙∙∙
X X
∙∙∙∙∙∙∙
X X
q
~
t
10 degree digit
: 0
~
9
1 degree digit
: 0
~
9
10 minute digit: 0
~
5
1 minute digit: 0
~
9
0.1
minute digit: 0
~
9
0.0
1 minute digit: 0
~
9
0.
00
1 minute digit: 0
~
9
0 (Fixed) 0 (Fixed) South latitude=0/North latitude=1 0 (Fixed) 100
degree digit
: 0
~
1
10
degree digit
: 0
~
9
1 degree digit
: 0
~
9
10 minute digit: 0
~
5
1 minute digit: 0
~
9
0.1
minute digit: 0
~
9
0.01
minute digit: 0
~
9
0.
00
1 minute digit: 0
~
9
0 (Fixed) 0 (Fixed) W
est longitude=0/East longitude=1
Latitude
Longitude
10000 meter digit:
0
~
1
1000 meter digit:
0
~
9
100 meter digit:
0
~
9
10 meter digit:
0
~
9
1 meter digit:
0
~
9
0.1
meter digit:
0
~
9
0 (Fixed) +=0/
–=1
Altitude
1
X X X X X X X 0 0 X 0 X X X X X X X X 0 0 X X X X X X X 0 X
2 3 4 5 6 7 8 9 10 11 12 13 14 15
*
*
*
*
:
q
~
t
: Latitude (ddºmm.mmm format)
y
~
!1
: Longitude (dddºmm.mmm format)
!2
~
!5
: Altitude (0.1 meter steps)
*
When reading the contents with no altitude, sends
!2
,
!3
,
!4
and
!5
as “FF.”
*
When sending the contents with no altitude, set
!2
,
!3
,
!4
and
!5
to “FF.”
•
Unproto Address setting
Command: 1A 05 0259
Set an unproto address of up to 56 characters.
See “Codes for character entries.” (p. 15)
•
Entering Object name or Item name
Command: 1A 05 0279, 0293
Enter an Object or Item name of up to 9 characters.
See “Codes for character entries.” (p. 15)
•
D-PRS Symbol setting
Command: 1A 05 0262 ~ 1A 05 0265,
1A 05 0281, 0295, 0306
First digit
Second digit
X
X
X
X
⁄, \, 0 to 9, A to Z can be used for the first digit
character.
See “Codes for character entries” for the second
digit character. (p.15)
•
D-PRS Comment setting
Command: 1A 05 0268 ~ 1A 05 0271
1A 05 0282, 0296, 0308
Set a comment of up to 43 characters.
See “Codes for character entries.” (p. 15)
•
GPS message setting
Command: 1A 05 0316
Set a GPS message of up to 20 characters.
See “Codes for character entries.” (p. 15)
•
Alarm area (Group) setting
Command: 1A 05 0317
q
X
X
X
X
0
w
e
X
10 min.
digit:
0
~
5
1 min.
digit:
0
~
9
0.1 min.
digit:
0
~
9
0.01 min.
digit:
0
~
9
0.001 min.
digit:
0
~
9
0 (fixed)
•
Data mode with filter width settings
Command: 1A 06
q
X X X X
w
01=FIL1
02=FIL2
03=FIL3
00=Data mode OFF*
01=Data mode ON
*
When 00 is set, also set 00 to
w
.
Remote control
17