ICE AIR VSHPW Operating And Maintenance Manual Download Page 3

3

Precautions and preparations listed are for general knowledge and to define basic guidelines. Local codes and existing practices should be observed and preformed by a professional. 

Due to Ice Air’s ongoing product development programs, the information in this document is subject to change without notice.

Consumer Reference Information

For safe and optimal enjoyment of your Ice Air unit, please read 
the following consumer safety and operating notes carefully before 
operating your equipment! 

p

 

RECOGNIZE THIS SYMBOL AS A SAFETY PRECAUTION.

p

!

  

WARNING: 

Ice Air will not be responsible for any injury or 

property damage arising from improper service, or service 
procedures. If you install or perform service on this unit, you 
assume responsibility for any personal injury or property 
damage which may result. Many jurisdictions require a license 
to install or service heating and air conditioning equipment.

p

!

  

WARNING HIGH VOLTAGE:

 

Disconnect all power before 

servicing or installing unit. Multiple power sources may be 
present. Failure to do so may cause property damage,  
personal injury or death.

Safety Guidelines 

Read this entire manual before operating the unit. 

p

!

  

 

WARNING:

 

This unit MUST be serviced only by professionally 

trained and qualified technicians. Do NOT attempt to maintain or 
service this unit on your own – severe injury and death can occur 
from electric shock, moving parts, and other hazards.

• 

Your Ice Air unit must be properly installed and commissioned 
to operate correctly. Improper unit installation, adjustment or 
commissioning, and/or improper heating system installation and 
connection can lead to equipment malfunction and hazardous 
operating conditions, and may void your warranty. If you have 
any doubt about the proper installation of your Ice Air unit, 
please contact your property manager at once to have a qualified 
technician inspect the equipment.

• 

Your Ice Air units must each be wired on an individual, dedicated 
electrical circuit with the correct voltage and proper amperage 
(capacity) to match the unit nameplate requirements.

• 

Each unit’s electrical circuit must have a proper overcurrent 
protection device, employing an approved circuit breaker or fuse 
of the proper rating under NEMA and local building codes.

p

!

  

WARNING: 

Every unit contains refrigerant within a sealed and 

pressurized refrigerant system. This system must not be opened 
or tampered with and any refrigeration system repairs MUST be 
carried out by trained technicians. Refrigerant must be properly 
handled and recycled per EPA regulations and guidelines.

p

!

  

WARNING:

 

Do NOT operate the unit with frayed, burnt or 

damaged electrical wires!

p

!

  

WARNING:

 

Do NOT operate the equipment when in doubt – 

have it inspected first!

IMPORTANT: 

It is not the intent of this maintenance manual to 

correct any installation deficiencies. If you have any doubt about the 
proper initial installation (or re-installation after servicing) of your Ice 
Air unit(s) – noisy or inefficient unit operation, frayed or damaged 
electrical connections, improper unit appearance, etc. – please 
contact a trained servicer or building maintenance staff immediately.

The following physical conditions must be maintained for 
proper unit operation:

Air flow must be unobstructed into and out of the unit return air 
opening.

•   Have the unit filter properly cleaned and serviced to prevent air 

blockage from dirt and dust within the filter media.

Intended for indoor use only.

Proper installation and operating environment must be maintained. 
Therefore:

•  Do not operate the unit in corrosive environments such as 

chemical plants, refineries or salt spray areas.

•  Operate only with proper electrical service and protective circuit 

breakers or fuses in place.

•  Operate only with all unit and enclosure sheet metal parts in 

place and properly installed.

•  In areas of high concentrations of dirt, dust, pet dander or 

pollutants, clean the filter often (at least monthly). 

•  Do not clean the unit with any solvents or cleaning solutions that 

may damage the equipment.

•  Understand and follow the unit operating instructions before 

using your Ice Air equipment.

Summary of Contents for VSHPW





















Reviews: