IC Realtime 1U POE NVR Series User Manual Download Page 45

Page: 45 / 291

Parameter

Description

Logout Time

In the

Auto Logout

box, enter the idle time for the Device. The

Device automatically logs out when it is not been operated for the
given time period. You will need to log in to the Device again.

The value ranges from 0 to 60. If set to "0" the system will not log
out once logged in automatically unless the unit power cycles.

Monitor Channel(s) when logout

. You can select the channels

that you want to continue monitoring when users are logged out.

IPC Time Sync

Syncs the Device time with IP camera.

IPC Time Sync Interval

In the

Interval

box, enter the interval for time sync.

Navigation Bar

Enable the navigation bar. When you click on the live view
screen, the navigation bar will be displayed.

Mouse Sensitivity

Adjust the speed of double-click by moving the slider.

The greater the value is, the faster the speed will be.

Step 2

Click

Apply

button to save settings.

4.1.4.1.2 Date and Time

Configures system’s time. You can enable NTP (Network Time Protocol) function so that the device
can sync time with the NTP server. NTP is enabled by default.
You can also configure date and time settings at a later time by selecting

Main Menu

> A

dvanced Settings > System Operation> General

Date&Time

Step 1 Click the

Date & Time

tab. See Figure 4-18.

Figure 4-18

Summary of Contents for 1U POE NVR Series




































































































































































































































































































Search results

Summary of Contents for 1U POE NVR Series

Reviews:

IC Realtime 1U POE NVR Series, User Manual, Page: 45 / 291

Search results

Summary of Contents for 1U POE NVR Series

Reviews: