manualshive.com logo in svg

IC Realtime 1U POE NVR Series, User Manual, Page: 35 / 291

Share
Download
IC Realtime 1U POE NVR Series User Manual Download Page 35

4.1.1 Booting up

● For device safety, connect the NVR to the power adapter first and then connect the device to the

power socket.

● Make sure the supplied rated input voltage matches the device power specifications.
● Make sure the power wire cable and source are in good condition.
● Always use a stable current, if necessary a UPS is a good alternative measure.

Step 1

Connect the device to the monitor and then connect a mouse.

Step 2

Connect the power cable.

Step 3

Click the power button at the front or rear panel and then boot up the device.

After the device has booted up, the system will display multiple-channel mode by default.

4.1.2 Device Initialization

If it is your first time using the device, set a login password for

admin

(system main

administrator user). You can select to use unlock pattern to log in or not at your own choosing.

For your device security, properly secure your login password of

admin

steps, and change the

password regularly.

Step 1 Power on your NVR. The

Device Initialization

interface will be displayed upon first time

boot up. See Figure 4-2

Figure 4-2

24

Summary of Contents for 1U POE NVR Series




































































































































































































































































































Reviews:

No comments