manualshive.com logo in svg

IC Realtime 1U POE NVR Series, User Manual, Page: 210 / 291

Share
Download
IC Realtime 1U POE NVR Series User Manual Download Page 210

4.9.2.3 BPS

The BPS section allows you to view the current video bit rate (kb/s) and resolution of the connected devices.
Select

Main Menu

>

Info

>

BPS

, the BPS interface will be displayed. See Figure 4-202.

Figure 4-202

4.9.3 Network

4.9.3.1 Online User

You can view the online user information or block any online user for a period of time. To block

an online user, click

and then enter the time that you want to block this user. The maximum

value you can set is 65535.
The NVR checks every 5 seconds to check whether there is any user added or deleted, and
update the user list accordingly.
Select

Main Menu

>

Info

>

Network

>

Online User

, the

Online User

interface will be

displayed. See Figure 4-205.

199

Summary of Contents for 1U POE NVR Series




































































































































































































































































































Reviews:

No comments