The
following
sections
provide
instructions
for
starting
the
SCSISelect
Utility
program
and
descriptions
of
the
menu
choices
that
are
available.
Note:
If
the
server
has
a
redundant
array
of
independent
disks
(RAID)
adapter
installed,
use
the
configuration
method
that
is
supplied
with
the
RAID
adapter
to
view
or
change
SCSI
settings
for
devices
attached
to
the
adapter.
Starting
the
SCSISelect
utility
program
Complete
the
following
steps
to
start
the
SCSISelect
Utility
program:
1.
Turn
on
the
server.
2.
When
the
<<<
Press
<CTRL><A>
for
SCSISelect
Utility!
>>>
prompt
appears,
press
Ctrl+A.
3.
When
the
message
Would
you
like
to
configure
the
host
adapter
or
run
the
SCSI
disk
utility?
appears,
make
your
selection
and
press
Enter.
4.
Use
the
arrow
keys
to
select
a
choice
from
the
menu.
v
Press
Esc
to
exit
the
SCSISelect
Utility
program.
v
Press
the
F5
key
to
switch
between
color
and
monochrome
modes
(if
your
monitor
permits).
5.
Follow
the
instructions
on
the
screen
to
change
the
settings
of
the
selected
items;
then,
press
Enter.
Choices
available
from
the
SCSISelect
menu
The
following
choices
appear
on
the
SCSISelect
Utility
menu:
v
Configure/View
Host
Adapter
Settings
Select
this
choice
to
view
or
change
the
SCSI
controller
settings.
To
reset
the
SCSI
controller
to
its
default
values,
press
F6;
then,
follow
the
on-screen
instructions.
You
can
view
or
change
the
following
controller
settings:
–
Host
Adapter
SCSI
ID
Select
this
choice
to
view
the
SCSI
controller
identification
(ID),
which
is
usually
7.
–
SCSI
Parity
Checking
Select
this
choice
to
view
the
assigned
value
of
Enabled.
–
Host
Adapter
SCSI
Terminatio
n
Select
this
choice
to
view
the
assigned
value
of
Automatic.
–
Boot
Device
Options
Select
this
choice
to
configure
startable-device
parameters.
Before
you
can
make
updates,
you
must
know
the
ID
of
the
device
whose
parameters
you
want
to
configure.
–
SCSI
Device
Configuration
Select
this
choice
to
configure
SCSI-device
parameters.
Before
you
can
make
updates,
you
must
know
the
ID
of
the
device
whose
parameters
you
want
to
configure.
Note:
The
Maximum
Sync
Transfer
Rate
is
the
transfer
rate
for
Ultra
SCSI
devices.
-
The
transfer
rate
for
Ultra160
low
voltage
differential
(LVD)
devices
is
160.0
MBps.
-
The
transfer
rate
for
Ultra2
SCSI
LVD
devices
is
80.0
MBps.
26
xSeries
440
Type
8687:
Hardware
Maintenance
Manual
Summary of Contents for xSeries 440 8687
