IBM SureMark 4610 1NF Page 26 Hardware Service Manual Download

Page: 26 / 112

Temperature and humidity limits

Shipping

-40° to 60° C (-40° to 140° F) with 5% to 100% relative humidity including condensation,
but excluding rain

Storage

0° to 60° C (32° to 140° F) with 5% to 80% relative humidity

Operating

5° to 40° C (42.8° to 104° F) with 8% to 80% relative humidity

Connector and port pin assignments

The following sections describe the connector pin assignments for the external connectors:

DC power connector

Table 5. Power supply pin assignments

Pin

Signal

+24 V dc

Not connected

Ground

12 V Powered USB (Display)

Table 6. Powered USB pin assignments

Pin

Signal

Vbus +5 V dc

Minus data

Plus data

Ground (Vbus)

Ground (+12 V dc)

+12 V dc

Ground (+12 V dc)

24 V Powered USB (Printer to Host)

Table 7. Powered USB 2 X 4 connector pin assignments

Pin

Signal

+5 V dcGround

+24 V dc

Vbus +5 V dc

+ Data

Ground

- Data

Ground

+24 V dc

Ground (Frame)

SureMark Hardware Service

Summary of Contents for SureMark 4610 1NF

















































































































Search results

Summary of Contents for SureMark 4610 1NF

Reviews:

Related manuals for SureMark 4610 1NF

Brands by name

Popular brands

IBM SureMark 4610 1NF, Hardware Service Manual

Search results

Summary of Contents for SureMark 4610 1NF

Reviews:

Related manuals for SureMark 4610 1NF

Brands by name

Popular brands