for
information
about
how
to
determine
the
routing
from
the
Ethernet-controller
ports
to
I/O
bays
for
your
blade
server.
You
do
not
have
to
set
any
jumpers
or
configure
the
controller
for
the
blade
server
operating
system.
However,
you
must
install
a
device
driver
to
enable
the
blade
server
operating
system
to
address
the
Ethernet-controller
ports.
For
device
drivers
and
information
about
configuring
your
Ethernet
controller
ports,
see
the
Ethernet
software
documentation
that
comes
with
your
blade
server,
or
contact
your
IBM
marketing
representative
or
authorized
reseller.
For
updated
information
about
configuring
the
controllers,
go
to
the
Barcelona
Computing
Centre
Web
site
at
http://www.bsc.es/projects/deepcomputing/linuxoncell/.
Note:
If
your
blade
server
contains
a
different
type
of
optional
Ethernet-compatible
switch
module
in
I/O
bay
1
than
the
switch
modules
that
are
mentioned
in
this
section,
see
the
documentation
that
comes
with
the
Ethernet
switch
module
that
you
are
using.
Updating
the
Ethernet
controller
firmware
To
update
the
Ethernet
controller
firmware,
you
must
download
an
update
package
from
http://www.ibm.com/support/us/en/.
This
section
describes
how
to
use
the
update
package
to
install
the
firmware
update.
The
update
package
consists
of
four
files:
v
A
file
containing
the
change
history
for
the
QS22
Ethernet
Controller
firmware.
This
has
a
.chg
extension.
v
A
file
containing
the
update
package.
This
has
an
.sh
extension.
v
A
readme
file
for
the
update
package.
This
contains
specific
installation
and
configuration
information.
v
An
XML
file.
This
file
is
for
use
by
IBM
Systems
Management
tools,
including
IBM
Director
Update
Manager,
UpdateXpress
CD,
and
UpdateXpress
System
Pack
Installer.
Using
the
update
package
The
package
consists
of
an
file
with
a
.sh
extension
that
runs
from
the
Linux
prompt.
It
has
a
number
of
options.
To
see
what
options
are
available,
run
the
package
without
any
options
or
with
the
-h
switch:
#
./brcm_fw_nic_2.0.3-e-1_rhel5_cell.sh
In
the
example
shown
above,
brcm_fw_nic_2.0.3-e-1_rhel5_cell.sh
is
the
name
of
the
firmware
update
package.
The
file
name
changes
according
to
the
version
of
the
firmware.
A
screen
similar
to
the
following
appears:
Usage:
-x
/someDirectory
-
Extract
the
payload
to
<some
directory>
-xr
/someDirectory
-
Extract
the
payload
plus
PkgSdk
files
to
<some
directory>
-xd
/dev/fd0
-
Create
a
DOS
bootable
diskette
-
Internel
floppy
drive
-xd
/dev/sda
-
Create
a
DOS
bootable
diskette
-
External
USB
floppy
drive
-u
-
Perform
update
unattended
-h
-
Display
this
help
screen
++debug
-
Display
helpful
debug
information
The
-xd
and
-x
options
are
not
supported
on
QS22.
Chapter
5.
Configuring
the
blade
server
51
Summary of Contents for QS22 - BladeCenter - 0793
