manualshive.com logo in svg

IBM P260, Installation And Service Manual

The Samsung P260 Software Setup Manual is a comprehensive guide that provides step-by-step instructions for setting up and optimizing your device's software. This essential manual can be easily downloaded for free from our website, ensuring you have all the necessary information at your fingertips.

Share
Download
background image

Installing a DIMM

The very low profile (VLP) dual-inline memory module (DIMM) is a tier 1 CRU. You can install it
yourself. If IBM installs a tier 1 CRU at your request, you will be charged for the installation. The low
profile (LP) DIMM is a tier 2 CRU. You can install it yourself or request IBM to install it, at no additional
charge, under the type of warranty service that is designated for the compute node.

About this task

To install a DIMM, complete the following steps:

Procedure

1.

Read the Safety topic and the “Installation guidelines” on page 35.

2.

Read the documentation that comes with the DIMMs.

3.

Shut down the operating system on all partitions of the compute node, turn off the compute node,
and remove the compute node from the IBM Flex System Enterprise Chassis. See “Removing the
compute node from an IBM Flex System Enterprise Chassis” on page 37.

4.

Carefully lay the compute node on a flat, static-protective surface, with the cover side up.

5.

Open and remove the compute node cover. See “Removing the compute node cover” on page 39.

6.

Locate the DIMM connectors on the system board. Determine the connector into which you will
install the DIMM. See “Supported DIMMs” on page 59.

7.

Touch the static-protective package that contains the part to any unpainted metal surface on the IBM
Flex System Enterprise Chassis or any unpainted metal surface on any other grounded rack
component, and then remove the new part from its shipment package.

8.

Verify that both of the connector retaining clips are in the fully open position.

9.

Turn the DIMM so that the DIMM keys align correctly with the connector on the system board.
Attention:

To avoid breaking the DIMM retaining clips or damaging the DIMM connectors, handle

the clips gently.

10.

Insert the DIMM (B) by pressing the DIMM along the guides into the connector.

Verify that each retaining clip (A) snaps into the closed position.

Figure 26. Installing a DIMM

58

Power Systems: IBM Flex System p260 and p460 Compute Nodes Installation and Service Guide

Summary of Contents for P260













































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for P260

Barco Encore Brochure preview
Encore
Brand: Barco Pages: 4
InFocus Mondopad INF8521 Hardware Manual preview
Mondopad INF8521
Brand: InFocus Pages: 45
Eneo VMC-17LCD-OPC1 Installation And Operating Insctruction Manual preview
VMC-17LCD-OPC1
Brand: Eneo Pages: 44
i3-TECHNOLOGIES i3TOUCH Premium P6505 T10 User Manual preview
i3TOUCH Premium P6505 T10
Brand: i3-TECHNOLOGIES Pages: 15
Gator GRV127KT User Manual preview
GRV127KT
Brand: Gator Pages: 12
IAdea XDS-151 User Manual preview
XDS-151
Brand: IAdea Pages: 12
ViewSonic VA2323w User Manual preview
VA2323w
Brand: ViewSonic Pages: 26
Hanns.G HW192 User Manual preview
HW192
Brand: Hanns.G Pages: 23
G-Lab MD2230 Instruction Manual preview
MD2230
Brand: G-Lab Pages: 27
A&D UA-767PBT-C Information preview
UA-767PBT-C
Brand: A&D Pages: 1
BAFANG DP C07.CAN User Manual preview
DP C07.CAN
Brand: BAFANG Pages: 14
FDS FD215CV-C-5 Installation And Operation Manual preview
FD215CV-C-5
Brand: FDS Pages: 25
Klipsch Reference Premiere RP-160M User Manual preview
Reference Premiere RP-160M
Brand: Klipsch Pages: 68
Xineron HEM191BP Instruction And Operation Manual preview
HEM191BP
Brand: Xineron Pages: 16
INNOLIVING INN-008 User Manual preview
INN-008
Brand: INNOLIVING Pages: 76
Hisense Babysense 5s User Manual preview
Babysense 5s
Brand: Hisense Pages: 2
Papenmeier Braillex EL 80s User Manual preview
Braillex EL 80s
Brand: Papenmeier Pages: 28
AOC Q27G2U User Manual preview
Q27G2U
Brand: AOC Pages: 27

Brands by name

Popular brands

Load more brands