manualshive.com logo in svg

IBM P260, Installation And Service Manual

The Samsung P260 Software Setup Manual is a comprehensive guide that provides step-by-step instructions for setting up and optimizing your device's software. This essential manual can be easily downloaded for free from our website, ensuring you have all the necessary information at your fingertips.

Share
Download
background image

3.

Press the power-control button to turn off the compute node. See “Turning off the compute node” on
page 13.

4.

Wait at least 30 seconds for the hard disk drive to stop spinning.

5.

Open the release handles, as shown in Figure 8 on page 37. The IBM Flex System p260 Compute
Node has one release handle. The IBM Flex System p460 Compute Nodehas two release handles. The
compute node can be moved out of the bay approximately 0.6 cm (0.25 inch).

6.

Pull the compute node out of the bay.

7.

Carefully lay the compute node on a flat, static-protective surface, with the cover side up.

8.

Place either a compute node filler or another compute node in the bay.

Reseating the compute node in a chassis

Reseat the compute node.

About this task

To reseat the compute node, complete the following steps:

Procedure

1.

Perform a virtual reseat of the compute node.

To perform a virtual reseat by using the IBM Chassis Management Module (CMM), go to
http://pic.dhe.ibm.com/infocenter/flexsys/information/topic/com.ibm.acc.8731.doc/
unmanaging_chassis.html.
To perform a virtual reseat by using the IBM Flex System Manager (FSM), go to http://
pic.dhe.ibm.com/infocenter/flexsys/information/topic/com.ibm.acc.8731.doc/
unmanaging_chassis.html.

2.

Is the problem resolved?

Yes:

This ends the procedure.

No:

Continue with the next step.

3.

Remove and replace the compute node into the IBM Flex System Enterprise Chassis.

a.

Remove the compute node from the IBM Flex System Enterprise Chassis. See “Removing the
compute node from an IBM Flex System Enterprise Chassis” on page 37.

b.

Install the compute node into the IBM Flex System Enterprise Chassis. See “Installing the compute
node in an IBM Flex System Enterprise Chassis” on page 93.

38

Power Systems: IBM Flex System p260 and p460 Compute Nodes Installation and Service Guide

Summary of Contents for P260













































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for P260

NEC MultiSync SC40 Specification preview
MultiSync SC40
Brand: NEC Pages: 2
NEC MultiSync V422 Setup Manual preview
MultiSync V422
Brand: NEC Pages: 2
NEC MultiSync V652 Specification preview
MultiSync V652
Brand: NEC Pages: 2
NEC MultiSync V463 Specification preview
MultiSync V463
Brand: NEC Pages: 4
NEC MultiSync V461 User Manual preview
MultiSync V461
Brand: NEC Pages: 36
NEC MultiSync V422 Control Manual preview
MultiSync V422
Brand: NEC Pages: 71
NEC ASPV46-AVT - AccuSync - 46" LCD TV Brochure preview
ASPV46-AVT - AccuSync - 46" LCD TV
Brand: NEC Pages: 4
NEC MultiSync XG-1352 Operation Manual preview
MultiSync XG-1352
Brand: NEC Pages: 38
Targa 19" User Manual preview
19"
Brand: Targa Pages: 22
Paradyne 9820 User Manual preview
9820
Brand: Paradyne Pages: 281
Barco MDRC-2124 User Manual preview
MDRC-2124
Brand: Barco Pages: 48
Barco MDRC-1119 TS User Manual preview
MDRC-1119 TS
Brand: Barco Pages: 66
Barco ILite 6 Service Manual preview
ILite 6
Brand: Barco Pages: 82
Barco MDSC-1119 Specifications preview
MDSC-1119
Brand: Barco Pages: 6
Barco HALO Specifications preview
HALO
Brand: Barco Pages: 2
Barco E-2320 C Installation & User Manual preview
E-2320 C
Brand: Barco Pages: 78
Barco DM-1126 Brochure preview
DM-1126
Brand: Barco Pages: 8
Barco Coronis 5MP Mammo Getting Started Manual preview
Coronis 5MP Mammo
Brand: Barco Pages: 88

Brands by name

Popular brands

Load more brands