IBM Infoprint 1130 Service Manual Download Page 83 | Manualshive

Page: 83 / 433

IBM Infoprint 1130 Service Manual Download Page 83

2-56

Service Manual

IBM Infoprint 1130/1140

Envelope Feeder Option Service Check

Service Tip: Check the envelope feeder paper path for any debris,
pieces of envelope and so on. If any other options are installed
make sure they are operating normally. If only the envelope feeder is
failing to operate correctly, continue with this service check.

Service Tip: The envelope feeder option receives its +5 V dc
operating voltage from the +24 V dc bulk at J1-7. If +24 V dc is not
present at J1-7, tray 1 is the only tray option that is recognized.

Note: If a 260 Paper Jam Check Envelope message displays,
check the

“Sub Error Codes for 9XX and 2XX Error Codes” on

Printer does not recognize the envelope feeder as an attached
input option.

FRU

Action

1

Envelope Feeder

Check to make sure the envelope
feeder is correctly installed and
mated to the autoconnect at the front
of the printer.

2

Front Autoconnect on
Printer

Check the connector for signs of
damage to the connector or
contacts. If you find damage, replace
the damaged cable/connector
assembly. Remove the envelope
feeder option and check the voltages
at the autoconnect on the front of the
printer. If incorrect, check the
interconnect board. If correct,
reinstall the envelope option and
continue with step 3.

«
...
81
82
83
84
85
...
»

Summary of Contents for Infoprint 1130


















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands