manualshive.com logo in svg

IBM Infoprint 1130, Service Manual

Share
Download
IBM Infoprint 1130 Service Manual Download Page 191

3-26

Service Manual

IBM Infoprint 1130/1140

To test the Bin Empty Sensor, actuate its flag in the paper output 
tray. To test the Bin Full Sensor and Near Full Sensor, first actuate 
the Bin Empty Sensor and then cover the Bin Full or Bin Near Full 
Sensor

Note:  OP=Open

CL=Closed

Base Sensor Test

This test is used to determine if the sensors located inside the 
printer are working correctly.

The following sensors can be checked:

Toner Optical Sensor

Input Sensor

Output Sensor (Fuser Exit)

Narrow Media Sensor

Front Door Sensor (Upper Front Cover)

To run the Base Sensor Test:

1. Select the Base Sensor Test.

– The operator panel displays OP for open and CL for closed.

2. Manually toggle the sensors by hand to verify that each sensor 

switches from open to closed.

StapleSmart Finisher Tests

Finisher Feed Test

This test is used to verify whether or not media can be fed to a 
finisher output bin and stapled. No information is printed on the test 
pages as the printhead is not turned on. Eight sheets of paper feed 
and then the pages staple.

Note:  This test can be run using any of the paper sizes supported 
by the printer.

The media is fed from the selected source and then outputted to the 
finisher output bin.

Summary of Contents for Infoprint 1130


















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands