Home
/
IBM
/
Infoprint 1130
/
Service Manual

IBM Infoprint 1130, Service Manual

Share

Page: 173 / 433

IBM Infoprint 1130 Service Manual Download Page 173

3-8

Service Manual

IBM Infoprint 1130/1140

Disabling Download Emulations

Error Code 964: Download Emulation CRC Failure. Checksum
failure detected in the emulation header or emulation file.

Error Code 965: Download Emulation Outdated. Time stamps
indicate the download emulation and RIP code are incompatible.

To help resolve Download Emulation problems the following steps
are necessary to instruct the printer to POR without activating any
download emulations.

To Disable the Download Emulation:

1. Turn the printer off.

2. Press and hold the Go and Menu buttons.

3. Turn the printer on and release the buttons once “Performing

Self Test” displays.

– Once the printer is idle, the emulation can be downloaded

again.

4. Program the download emulation into the code overlay card

assembly again.

5. If these steps do not resolve the problem, replace the code

overlay card assembly and download the emulation again.

Duplex Tests

Duplex Quick Test

This test is used to verify that the Duplex Option Top Margin is set
correctly. This test prints a duplexed version of the Quick Test Page
that can be used to adjust the Top Margin for the backside of the
duplexed page. You can run one duplexed page (Single) or continue
printing duplexed pages (Continues) until Return/Stop is pressed.

The paper you choose to print the page on should be either Letter or
A4.

To run the Duplex Quick Test:

1. Select Duplex Quick Test from the menu.

2. Select Single or Continuous.

«
...
171
172
173
174
175
...
»

Summary of Contents for Infoprint 1130


















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands