Home
/
IBM
/
Infoprint 1130
/
Service Manual

IBM Infoprint 1130, Service Manual

Share

Page: 166 / 433

IBM Infoprint 1130 Service Manual Download Page 166

Diagnostic Aids

3-1

IBM Infoprint 1130/1140

3. Diagnostic Aids

This chapter explains the tests and procedures to identify printer
failures and verify repairs have corrected the problem.

Diagnostic/Configuration Menu

Diagnostic Menu - Used to help test and diagnose printer and
attached option problems.

Configuration Menu - Contains a set of menus, settings, and
operations that are generally used to configure the printer for
operation. Such menu setting as Resetting the Maintenance Count
is included in this menu.

The following table lists the tests as they are displayed on the
Diagnostic Test Menu screens.

Tests

Refer to Test Page

Registration
If selected, the following menu selections are
available:

• The Video Frequency Test runs

automatically, then the margin values
screen is displayed.

“Registration” on
page 3-28

Print Tests
If selected, the following menu selections are
available:

1.Tray x is displayed (x-Tray selected

1,2,3,4,or 5).

2.MP Feeder is displayed.
3.Envelope Feeder (if installed)
4.Print Quality Test Pages are displayed.

“Print Tests” on
page 3-33

«
...
164
165
166
167
168
...
»

Summary of Contents for Infoprint 1130


















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands