DANGER
An
electrical
outlet
that
is
not
correctly
wired
could
place
hazardous
voltage
on
metal
parts
of
the
system
or
the
devices
that
attach
to
the
system.
It
is
the
responsibility
of
the
customer
to
ensure
that
the
outlet
is
correctly
wired
and
grounded
to
prevent
an
electrical
shock.
(D004)
Position
the
Tape
Drive
Position
the
unit
so
it
is
convenient
to
the
server.
The
only
restrictions
are
the
length
of
the
power
cord
and
the
length
of
the
cable
to
the
server.
Recommended
locations
are:
v
Away
from
high-traffic
areas,
especially
if
the
floor
is
carpeted.
v
Out
of
printer
or
copy
rooms
to
avoid
toner
and
paper
dust.
Do
not
store
paper
supplies
next
to
any
unit.
v
Away
from
moving
air,
such
as
doorways,
open
windows,
fans,
and
air
conditioners.
v
Off
the
floor.
v
In
a
horizontal
position.
v
Where
the
tape
cartridge
can
be
easily
inserted.
The
unit
should
not
be
stacked.
Do
not
place
anything
on
top
of
the
unit.
Install
the
SAS
Host
Adapter
Card
(if
required)
If
there
are
no
other
devices
attached
to
your
server,
a
SAS
host
adapter
card
may
need
to
be
installed
in
the
server.
To
install
an
adapter,
refer
to
the
instructions
that
accompany
it,
as
well
as
to
the
section
about
host
adapter
card
installation
in
your
server’s
documentation.
For
a
list
of
supported
adapters
and
required
interposers,
visit
the
web
at
http://www.ibm.com/storage/lto
Connect
the
SAS
Bus
Cable
The
requirements
for
SAS
bus
connections
are
different
than
for
the
SCSI
bus.
Each
tape
drive
is
required
to
have
a
dedicated
bus
to
the
initiator,
referred
to
as
point-to-point
connection.
SAS
architecture
does
not
support
multiple
tape
drives
connected
to
a
single
host
adapter
port.
The
maximum
SAS
cable
length
that
can
be
used
to
connect
the
host
adapter
to
the
tape
drive
is
5.5
m.
To
connect
the
cable:
1.
Ensure
the
tape
drive
is
powered
OFF.
2.
Since
there
are
several
types
of
SAS
connectors,
verify
the
SAS
cable
has
the
correct
connectors
for
the
SAS
host
adapter
and
for
the
tape
drive.
3.
The
tape
drive
has
one
SAS
port
allowing
the
drive
to
be
connected
to
only
one
server.
See
2-4
TS2240
Tape
Drive
Setup,
Operator
and
Service
Manual
Summary of Contents for H4S
