IBM Flex System x440 Compute Node Installation And Service Manual Download Page 554 | Manualshive

Page: 554 / 584

background image

Installation tool

Microprocessor

Screws

c.

Twist the handle on the installation tool clockwise and lift the
microprocessor out of the socket.

Handle

Installation
tool

Microprocessor

What to do next

If you are instructed to return the microprocessor and heat sink, follow all
packaging instructions, and use any packaging materials for shipping that are
supplied to you.

Installing a microprocessor and heat sink

Use this information to install a microprocessor and heat sink.

Before you begin

Note:

This procedure should be performed only by trained service technicians.

The architecture of the Intel Sandy Bridge-EP 4S and DMI switching of
microprocessor sockets 1 and 2 allow for the processors to be populated as shown
in the following figures.

542

IBM Flex System x440 Compute Node Types 7917 and 2584: Installation and Service Guide

«
...
552
553
554
555
556
...
»

Summary of Contents for Flex System x440 Compute Node









































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Flex System x440 Compute Node

8BIG RACK THUNDERBOLT 2

Brand: LaCie Pages: 28

Brand: YOKOGAWA Pages: 22

Brand: IBM Pages: 142

Brand: AIC Pages: 101

AlphaServer ES45 1B

Brand: Compaq Pages: 322

Brand: Advantech Pages: 38

Brand: XtendLan Pages: 28

Brand: XtendLan Pages: 50

Terminal Server

Brand: Black Box Pages: 131

Brand: Eelectron Pages: 42

Brand: Eelectron Pages: 113

Brand: 10ZiG Technology Limited Pages: 2

Brand: Celestix Pages: 68

Brand: Supero Pages: 80

Brand: Xiva Pages: 37

PS 4000 Gen2 Series

Brand: PAC STORAGE Pages: 108

Brand: Oracle Pages: 204

Brand: CAAS Audio Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands