IBM Flex System x440 Compute Node Installation And Service Manual Download Page 480 | Manualshive

Page: 480 / 584

background image

Cannot ping the IBM Flex System Manager management node on
the data network

Use the information in this section to troubleshoot the compute node when one or
more compute nodes cannot ping the management node on the data network.

Single node cannot ping the management node in the same chassis:

Use the information in this section to troubleshoot a single compute node that
cannot ping the IBM Flex System Manager management node in the same chassis
on the data network.

Action

Complete the following steps until the problem is solved:

1.

Make sure that the management node is powered on and is not hung, by
logging in to the management node. If you are unable to log in from the
management network, attempt to log in from the data network. If the
management node is powered on and hung, perform a virtual reseat of the
management node from the CMM.

2.

Make sure that the I/O module is powered on and is not hung, by pinging the
I/O module from the management node. If the I/O module is powered on and
hung, reset the I/O module. Make sure that the correct ports are enabled for
the node on the I/O module.

3.

Make sure that the compute node is the only one in the chassis that the
management node cannot ping. If it is not, follow the steps in “Multiple nodes
cannot ping the management node in the same chassis” on page 469.

4.

Make sure that the configuration settings in the node are correct and that the
port is enabled.

5.

Check http://www.ibm.com/supportportal/ for any firmware updates that
might apply to this issue. You can view the release notes for a firmware update
to determine the issues that are addressed by the update.

6.

Check http://www.ibm.com/supportportal/ for any service bulletins that are
related to network connectivity.

7.

Remove the compute node and make sure that the connectors on the midplane
and the node are not damaged.

8.

(Trained service technician only) Complete the following steps:

a.

Force the link/duplex speed.

b.

Check the connectors on the node and the midplane to make sure that no
pins are bent.

c.

Replace the system board in the compute node.

Single node cannot ping the management node in a different chassis:

Use the information in this section to troubleshoot a single compute node that
cannot ping the IBM Flex System Manager management node in a different chassis
on the data network.

Action

Complete the following steps until the problem is solved:

1.

Make sure that the management node is powered on and is not hung, by
logging in to the management node. If you are unable to log in from the

468

IBM Flex System x440 Compute Node Types 7917 and 2584: Installation and Service Guide

«
...
478
479
480
481
482
...
»

Summary of Contents for Flex System x440 Compute Node









































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Flex System x440 Compute Node

Brand: Oki Pages: 121

SUPERSERVER 6021F

Brand: Supermicro Pages: 116

STRATOS S400-X44E

Brand: Quanta Computer Pages: 251

Brand: B&B Electronics Pages: 2

OmniStor 4900F Series

Brand: Rackable Systems Pages: 196

8676 - Eserver xSeries 335

Brand: IBM Pages: 172

System x3650 M4 BD Type 5466

Brand: IBM Pages: 786

Brand: Supermicro Pages: 113

PLATINUM 1500 IR M5

Brand: MAXDATA Pages: 44

TS-73AeU Series

Brand: QNAP Pages: 70

Brand: Rasilient Pages: 30

Brand: Simpact Pages: 86

Brand: Bosanova Pages: 2

Brand: Bosanova Pages: 2

Brand: Bosanova Pages: 2

Brand: Blonder tongue Pages: 20

Brand: Black Box Pages: 3

Brand: Promise Technology Pages: 259

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands