IBM Flex System x440 Compute Node Installation And Service Manual Download Page 30

Page: 30 / 584

System-board LEDs

The following illustration shows the location of the LEDs on the system board.

DIMM
error

Microprocessor 3

error

Microprocessor 4

error

Microprocessor 2

error

Microprocessor 1

error

Battery
error

Storage
backplane 1
error

Storage
backplane 2
error

System-board switches

Use this information to locate the system-board switches.

The following illustration shows the location of the switch block on the system
board.

IBM Flex System x440 Compute Node Types 7917 and 2584: Installation and Service Guide

Summary of Contents for Flex System x440 Compute Node









































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Flex System x440 Compute Node

Reviews:

Related manuals for Flex System x440 Compute Node

Brands by name

Popular brands

IBM Flex System x440 Compute Node, Installation And Service Manual

Search results

Summary of Contents for Flex System x440 Compute Node

Reviews:

Related manuals for Flex System x440 Compute Node

Brands by name

Popular brands