Support
CD.
If
this
CD
did
not
come
with
your
server,
you
can
download
the
IBM
ServeRAID-7e
(
Adaptec
HostRAID
)
Support
CD
from
the
IBM
Web
site
at
http://www.ibm.com/pc/support/.
Enabling
the
SCSI
HostRAID
feature
Complete
the
following
steps
to
enable
the
SCSI
HostRAID
feature:
1.
Turn
on
the
server.
2.
When
the
prompt
Press
<CTRL><A>
for
SCSISelect
Utility
appears,
press
Ctrl+A.
If
you
have
set
an
administrator
password,
you
are
prompted
to
type
the
password.
3.
Use
the
arrow
keys
to
select
the
channel
for
which
you
want
to
change
settings
and
press
Enter.
4.
Select
Configure/View
SCSI
Controller
Setting
;
then,
select
HostRAID
.
5.
Select
Enabled
.
6.
Press
Esc;
then,
select
Yes
to
save
the
changes.
Using
the
SCSI
HostRAID
feature
The
instructions
in
this
section
describe
how
to
access
the
SCSI
HostRAID
feature
from
the
SCSISelect
Utility
program
and
perform
an
initial
RAID
level-1
configuration.
If
you
install
a
different
type
of
RAID
adapter
in
the
server,
use
the
configuration
method
described
in
the
instructions
that
come
with
that
adapter
to
view
or
change
SCSI
settings
for
attached
devices.
See
the
documentation
on
the
ServeRAID-7e
(Adaptec
HostRAID)
Support
CD
for
additional
information
about
how
to
use
the
SCSI
HostRAID
feature.
Configuring
the
controller
Complete
the
following
steps
to
use
the
SCSI
HostRAID
feature
to
configure
a
RAID
level-1
array:
Note:
You
must
at
least
two
hard
disk
drives
installed
in
the
server
to
configure
a
RAID
level-1
array.
1.
From
the
SCSISelect
Utility
main
menu,
select
Configure/View
HostRAID
Settings
.
2.
From
the
list
of
ready
drives,
type
C
to
create
an
array.
3.
Select
RAID-1
when
asked
to
select
the
RAID
type.
4.
From
the
list
of
ready
drives,
select
the
two
drives
that
you
want
to
group
into
the
array.
5.
Select
Create
new
RAID-1
.
6.
Type
an
identifier
for
the
array.
7.
Select
Yes
to
create
the
array.
8.
Press
Esc
to
exit
the
utility.
9.
Restart
the
server.
Viewing
the
configuration
You
can
use
the
SCSISelect
Utility
program
to
view
information
about
the
SCSI
controller.
From
the
list
of
available
arrays,
select
an
array
and
press
Enter.
Press
Esc
to
exit
the
utility.
Chapter
2.
Configuring
the
server
25
Summary of Contents for eServer xSeries 236
