FRU
part
number
44P2645,
only
if
the
firmware
on
the
system
is
3H030916
or
later.
Do
not
mix
the
two
versions
without
the
firmware
level
being
3H030916
or
later.
2.
Make
sure
that
the
BPR
release
levers
are
in
the
UP
position.
Slide
the
unit
into
slot
until
one
inch
from
BPE.
Using
both
hands
on
the
front
of
the
BPR,
firmly
and
quickly
seat
the
BPR
against
the
backplane.
3.
Tighten
the
left
fastener
four
turns
with
torque
tool
followed
by
four
turns
to
the
right
fastener.
Torque
the
left
fastener
to
completion,
followed
by
the
right
fastener.
Return
to
the
left
fastener
and
ensure
that
it
is
properly
torqued.
4.
Move
the
BPR
release
levers
to
the
DOWN
position.
5.
If
the
battery
feature
is
installed,
reconnect
the
battery
cable
to
the
connector
on
the
front
face
of
the
BPR.
6.
Manually
turn
on
the
IBF
circuit
breaker.
7.
Move
the
BPR
Lock/Unlock
switch
to
lock
(power
switch
to
the
left).
8.
Press
the
white
Service
Complete
button
on
the
UEPO
switch
to
indicate
completion
of
this
procedure,
if
this
repair
was
completed
during
a
system
outage,
bring
the
system
back
up.
9.
If
a
high
performance
switch
is
installed
in
or
attached
to
the
system,
perform
the
steps
described
in
to
insure
that
the
new
BPR
contains
the
correct
code.
Bulk
Power
Controller
(BPC)
The
BPC
is
located
immediately
above
the
top
BPR.
Attention:
This
service
procedure
may
produce
other
power
error
code(s)
(101x
xxxx)
between
the
time
the
Start
Service
button
is
pressed
and
the
Service
Complete
button
is
pressed,
during
concurrent
repair.
If
normal
system
operation
continues,
as
described
by
this
procedure,
ignore
these
error
codes.
Removal
Attention:
The
BPC
unit
weighs
approximately
3.18
kg
(7
lbs).
1.
Locate
the
BPC
to
be
replaced.
2.
Note
the
state
of
the
BPC
LEDs.
3.
Press
the
green
Start
Service
button
on
the
UEPO
switch.
4.
Proceed
only
if
the
ENBL
(Good)
LED
goes
off
or
the
repair
has
been
scheduled.
If
the
repair
has
been
scheduled,
power
off
the
system
as
described
in
then
return
here.
5.
Check
the
ENBL
(Good)
LED
for
all
the
BPRs
(LED
on
right
side
of
FRU)
on
same
BPA
side.
For
each
BPR
that
has
this
LED
in
the
ON
state,
manually
slide
the
power
switches
to
the
right.
Attention:
Do
not
switch
off
units
where
this
LED
is
already
off.
6.
Verify
that
all
cables
are
labeled
for
plug
location
and
then
unplug
the
cables
from
the
BPC.
7.
Loosen
the
left
and
right
fasteners
using
the
torque
tool
(part
number
6422789).
Slide
the
unit
out
of
the
slot.
Chapter
9.
Removal
and
Replacement
Procedures
861
Summary of Contents for eserver pSeries 690
