IBM eserver iSeries 270 Installation Manual Download | Manualshive

Page: 28 / 40

background image

__ 8.

Install the remaining memory cards.

__ 9.

When you finish installing all the memory cards, slide the card assembly
into the system unit. Push on both card latches at the same time. Close the
latches when you cannot push the card assembly any further into the

system unit.

__ 10.

Reinstall the access cover.

__ 11.

You have completed the installation of the memory cards in your system.

Go to “Install system unit covers”.

Install system unit covers

__ 1.

Remove the wrist strap.

__ 2.

Figure 21 on page 25

shows how to install the system unit side cover by

aligning the tabs on the top and bottom edge. Press forward to make sure
that all tabs enter the slots. Slide the cover toward the front of the system
unit until it stops and install the screws.

Figure 20. Install Memory Cards

24

30xx Memory Card Installation V5R2

«
...
26
27
28
29
30
...
»

Summary of Contents for eserver iSeries 270









































Reviews:

No comments

Related manuals for eserver iSeries 270

SX-2000A Series

Brand: GDC Pages: 185

Brand: Sollae Systems Pages: 45

Brand: Crestron Pages: 2

SUPERSERVER 5015M-NT

Brand: Supero Pages: 134

Brand: Fujitsu Pages: 200

EMC VxFlex Appliance R840

Brand: Dell Pages: 44

EqualLogic PS4000

Brand: Dell Pages: 73

EMC PowerProtect DD6400 System

Brand: Dell Pages: 46

EqualLogic PS5500

Brand: Dell Pages: 8

Brand: Dell Pages: 22

External OEMR R210II

Brand: Dell Pages: 126

External OEMR R210

Brand: Dell Pages: 144

External OEMR XL R210

Brand: Dell Pages: 72

POWER EDGE SC1430

Brand: Dell Pages: 160

EMC PowerEdge XE8545

Brand: Dell Pages: 33

EMC PowerEdge T640 D24XR

Brand: Dell Pages: 166

Brand: Dell Pages: 68

Brand: Dell Pages: 66

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands