IBM Elastic Storage System 3200 Hardware Planning And Installation Manual Download Page 79 | Manualshive

Page: 79 / 156

background image

5. Complete the steps outlined in the “Completing the ESS 3200 installation at the customer site (SSR

task)” on page 64.

Install and connect management server 5105-22E

For information about installing the management server, see Install and Connect the ESS Management

Server 5105-22E on the IBM Worldwide Customized Installation Instructions (WCII) website.

Connect power cords to rack PDUs

For information, see Connect power cords to rack PDUs on the IBM Worldwide Customized Installation

Instructions (WCII) website.

ESS 5000 SCx/SLx network cabling

In case your configuration includes ESS 5000 with SCx or SLx network cabling, see the following links:
• For information about 5147-SCx networking cabling, see ESS SCx network cabling on the IBM

Worldwide Customized Installation Instructions (WCII) website.

• For information about 5147-SLx networking cabling, see ESS SLx network cabling on the IBM Worldwide

Customized Installation Instructions (WCII) website.

Connect AC (wall) power to the rack PDUs

For information, see Connect AC (wall) power to the rack PDUs on the IBM Worldwide Customized

Installation Instructions (WCII) website.

Power On switches, storage enclosures, and servers

For information, see Power on switches, storage enclosures, and servers on the IBM Worldwide

Customized Installation Instructions (WCII) website.

Check servers with

essutils

tool

For information, see Check servers with essutils tool on the IBM Worldwide Customized Installation

Instructions (WCII) website.

Best practices for network configuration (Customer reference task)

Use this section for best practices and guidance when you fill out the Installation worksheet.
Using these best practices, the customer is aided to select IP addresses for the management interfaces

and fill out the Installation worksheet. This information from the customer is required for the SSR to

pre-set the required IP addresses needed for successful storage deployment. Once the SSR is finished,

the hardware and management networking is ready for the next phase of the install (Quick deployment

guide), see the Quick Deployment guide in the IBM Elastic Storage System 3200 Documentation website.
The SSR takes the input from the worksheet and implements the requested IP addresses. The information

below is general guidance and is purely for example reasons. If the SSR does not receive desired IP

addresses at time of hardware installation, they would set default IP addresses on the nodes.

Management server best practices (EMS)

Ensure that each IP in the worksheet is on the same subnet. Recommended subnet is /24

(255.255.255.0).
Management Network IPs:

Subnet: 192.168.45.0/24

IP Address: 192.168.45.20

Chapter 4. Installing 61

«
...
77
78
79
80
81
...
»

Summary of Contents for Elastic Storage System 3200





























































































































































Reviews:

No comments

Related manuals for Elastic Storage System 3200

05DTMBAX0307DD-V1

Brand: Mercia Garden Products Pages: 9

Brand: Morrow Pages: 46

Brand: Xigmatek Pages: 2

Brand: Onnto Pages: 40

Brand: Seagate Pages: 68

Brand: IBM Pages: 44

Brand: Y-E Data Pages: 48

Leicester KIS12964

Brand: Gardiun Pages: 40

Brand: QNAP Pages: 68

CLARiiON CX4-120

Brand: EMC Pages: 62

Option GlobeTrotter

Brand: ORANGE Pages: 34

Brand: Clarke Pages: 8

Ultrastar 15K73

Brand: Hitachi Pages: 273

Travelstar 5K500

Brand: Hitachi Pages: 5

Travelstar 5K500.B

Brand: Hitachi Pages: 5

Travelstar 40GN

Brand: Hitachi Pages: 2

Travelstar 4K40

Brand: Hitachi Pages: 2

Travelstar 4K80

Brand: Hitachi Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands