manualshive.com logo in svg

IBM CS821, Service Manual

Share
Download
IBM CS821 Service Manual Download Page 31

6.

Place the disk drive backplane and cables on the table.

Replacing the disk drive backplane in the 8001-12C or 8005-12N

Learn how to replace the disk drive backplane in the IBM Power System S821LC (8001-12C) or the IBM
CS821 (8005-12N) system.

Procedure

1.

Ensure that you have the electrostatic discharge (ESD) wrist strap attached. If not, attach it now.

2.

Remove the replacement disk drive backplane and cables from the protective plastic envelope.

3.

Move the cables from the old disk drive backplane to the new card.

4.

Replace the disk drive backplane as shown in Figure 14 on page 16.

a.

Insert the disk drive backplane (A) into the system using the alignment slots (B) in the chassis.

b.

Snap the card into place so that it is held by the retaining clips (C).

c.

Replace the two screws (D), one on each side, in the top of the disk drive backplane.

Figure 13. Removing the disk drive backplane and screws

Removing and replacing parts

15

Summary of Contents for CS821























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands