IBM CPC700 User Manual Download Page 238 | Manualshive

Page: 238 / 268

background image

10-4

Interrupt Controller

10.4.2 Interrupt Vector Base Address

This register contains the base address of the vector generated for interrupts programmed to generate an
external interrupt to the processor. It is added to the interrupt vector offset to create a vector address spe-
cific to each interrupt.

10.4.3 Interrupt Enable/Disable

Each bit of the Enable/Disable register will be used to enable/disable a single interrupt bit in the Status reg-
ister. If enabled the active status bit will generate an interrupt signal to the processor. This will be used fre-
quently by the software while handling interrupts.

10.4.4 INT/MCP Interrupt

Each interrupt can be programmed as INT or MCP. When properly enabled, INT programmed interrupts will
drive the CPC700’s IRQ_OUT_N output signal to trigger an external interrupt to the processor. MCP pro-
grammed interrupts, when properly enabled and when the MCP enable bit (bit 1) of the PRIFOPT1 register
is set, will drive the CPC700’s MCP_N output signal to trigger a machine check exception to the processor.

10.4.5 Polarity

Each bit of this register is used for determining whether a single interrupt input will be positive active or
negative active. For level sensitive interrupts, this bit determines the active polarity. For edge triggered
inputs, it determines whether a rising edge or a falling edge will cause an interrupt.

10.4.6 Edge/Level Sensitivity

Each bit of this register will correspond to an asynchronous interrupt input. The bits in this register will be
used to program the input as an edge triggered interrupt or a level sensitive interrupt.

10.5 Universal Interrupt Controller Registers

Interrupt controller registers are memory mapped to the locations shown in Table 99. The following sec-
tions detail the registers of the UIC.

«
...
236
237
238
239
240
...
»

Summary of Contents for CPC700













































































































































































































































































Reviews:

No comments

Related manuals for CPC700

Brand: Jafar Pages: 10

Brand: Jafar Pages: 8

Brand: Panasonic Pages: 45

Brand: Eaton Pages: 12

Brand: Harpo Pages: 35

Brand: Hardi Pages: 2

Brand: Lakeshore Pages: 186

Brand: Nacon Pages: 24

Brand: NAD Pages: 4

Brand: NAD Pages: 4

Brand: Sanhua Pages: 3

Brand: QED Pages: 26

Brand: ZKTeco Pages: 20

Brand: ZKTeco Pages: 8

Brand: ZKTeco Pages: 10

Brand: ZKTeco Pages: 121

Brand: ZKTeco Pages: 12

Brand: ZKTeco Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands