background image

 
 

© Copyright IBM Corporation 2020, 2021               Customer Install Guide, 100G Switch  

16 

Operating Environment 

Cloud Pak for Data System components are designed to work together as a system in 
an ASHRAE A2 environment.  .  
 
Table 2: Operating Environment 

Environment 

Recommended 

operating 

Allowable 

operating 

Nonoperating 

ASHRAE 

 

A2 

 

Airflow Direction 

 

Front-to-back 

 

Temperature 

18C 

– 27C (61F -

80F) 

10C 

– 35C (50F-

95F) [1, 5] 

5C 

– 45C (41F – 

113F) 

Humidity  

25% - 60% 

noncondensing [2, 

4] 

20% - 80% 

noncondensing [2, 

4] 

8% - 85% [4] 

Maximum 
Operating Altitude 

 

3050m (10,000 ft) 

[1] 

 

Shipping 
Temperature 

 

 

-40C 

– 60C (-40F – 

140F) [3, 4] 

Shipping relative 
humidity 

 

 

8% - 90% [4] 

[1] Derate maximum allowable dry-bulb temperature by 1C (1.8F) per 300m (984 ft) 
increase in altitude above 950m (2,953 ft)  
[2] Maximum dewpoint 21°C (70°F) 
[3] Short term temperature only for servers with SSDs 
[4] Unit must acclimate to data center environment before unboxing to prevent 
condensation. 
[5] PDUs do not have fresh air cooling and can function in 60C (140F) environments 

 

 

Summary of Contents for 3454-CAC









































Reviews: