background image

3

INSTALLATION AND OPERATING INSTRUCTIONS

DC SERIES BOILERS / WATER HEATERS  

DC 15-95, DC 15-96, DC 20-125, DC 33-160

SPECIFICATION

DC 15-95

DC 15-96

DC 20-125 DC 33-160

CSA Input (Natural Gas or Propane) – MBH

15 - 95

15 - 96

20 - 125

33 - 160

CSA Input (Natural Gas or Propane) – KW

4.4 - 27.8

4.4 - 28.1

5.6 - 36.6

9.7 - 46.9

CSA Output – MBH

14.4 - 85.5

14.5 - 85.9

18.6 - 110.8

30.4 - 140.0

CSA Output - KW

4.2 - 25.0

4.3 - 25.2

5.4 - 32.5

8.9 - 41.0

DHW - CSA Input (Natural Gas or Propane) - 

MBH

15 - 95

15 - 96

20 - 125

33 - 124

DHW - CSA Input (Natural Gas or Propane) - KW

4.4 - 27.8

4.4 - 28.1

5.6 - 36.6

9.7 - 36.3

A.F.U.E

95%

96%

95%

94%

Min Gas Pressure (Nat. Gas or Propane) – inch 

w.c.

5

5

5

5

Max Gas Pressure (Nat. Gas or Propane) – inch 

w.c.

14

14

14

14

Power (120Vac/60Hz) - Watts @ full fire with 

internal pump

128

128

130

164

Weight (empty) – lbs/Kg

97 / 44

105 / 48

105 / 48

105 / 48

Pressure Vessel water content – USG/Liters

0.37 / 1.4

0.5 / 1.9

0.5 / 1.9

0.5 / 1.9

Max boiler flow rate - USgpm

10

10

11

11

Min boiler flow rate - USgpm

2

2

3

3

Max Operating Pressure – Space Heating Coil - 

psig

43.5

43.5

43.5

43.5

Max Operating Pressure – Domestic Hot Water 

Coil - psig

150

150

150

150

Approved installation altitude - ASL

10,000 ft

10,000 ft

10,000 ft

10,000 ft

Ambient Temperature – Low (°F/°C)

32 / 0

32 / 0

32 / 0

32 / 0

Ambient Temperature – High (°F/°C)

122 / 50

122 / 50

122 / 50

122 / 50

Max relative humidity (non-condensing)

90%

90%

90%

90%

Min water Temperature - Space Heating (°F/°C)

50 / 10

50 / 10

50 / 10

50 / 10

Max water Temperature – Space Heating (°F/°C)

194 / 90

194 / 90

194 / 90

194 / 90

Min water Temperature – Domestic Hot Water 

(°F/°C)

104 / 40

104 / 40

104 / 40

104 / 40

Max water Temperature – Domestic Hot Water 

(°F/°C)

149 / 65

149 / 65

149 / 65

149 / 65

Min flow rate to activate DHW heating - USgpm

0.5

0.5

0.5

0.5

Max flow rate DHW heating - USgpm

3.0

3.0

4.0

4.0

Max equivalent vent length 3" (each side)

120'

120'

120'

120'

Max equivalent vent length 2" (each side)

35'

35'

35'

35'

*  Natural Gas boilers / water heaters require a Propane conversion kit (see page #3-2,  Table 10) to be ordered separately if converting a Natural Gas boiler / water 

heater to Propane. Propane (LP) boilers / water heaters require a Natural Gas conversion kit (see page #3-2,  Table 10) to be ordered separately if converting a 

Propane boiler / water heater to Natural Gas.

†  boilers / water heaters are shipped with 30 psig pressure relief valve

SPECIFICATIONS

Summary of Contents for DC Series



















































































Reviews: