IAI LQ-401CL User Manual Download Page 43

Page: 43 / 73

LQ-401CL

6.3.9 Compatibility of trigger modes and functions

Trigger

Image output format

Gain

Offset

Mode

Origin

Full

resolution

Binnin

Sub

sampling

Windowin

Master

Tracking

Individual

Master

tracking

Individua

No-shutter

Internal

◎

Externa

Shutter-Selec
t

Internal

◎

Externa

PWC

Externa

◎

Trigger

Shading

correction

AWB

Test

pattern

Auto Line

Rate

Mode

Origin

FLAT COLOR Gain Shutter

No-shutter

Internal

◎

External

○

Shutter-Select

Internal

◎

External

○

PWC

External

○

Note:

◎

They can be used together.

○

They can be used together but when the compensation data is acquiring or test signal

is displaying, the trigger pulse should be continuously input.

They cannot be used together.

6.3.10 Trigger modes and auto white balance modes matrix table

Trigger

Control

One-push

gain

One-push

shutter

No-shutter

Internal

yes

External

yes

Shutter-Select

Internal

yes

External

yes

PWC

Internal

yes

Summary of Contents for LQ-401CL










































































Search results

Summary of Contents for LQ-401CL

Reviews:

Brands by name

Popular brands

IAI LQ-401CL, User Manual

Search results

Summary of Contents for LQ-401CL

Reviews:

Brands by name

Popular brands