manualshive.com logo in svg

IAI LQ-401CL, User Manual

Share
Download
IAI LQ-401CL User Manual Download Page 37

LQ-401CL

 

 

36 

 

Note: EEN uses channel with the largest exposure value 

 

Fig.40      Shutter–Select mode/Sub-sampling and Window/ Internal 

 

6.3.5      Shutter-Select mode with external trigger   

 
In this mode, the exposure and readout is activated by the external trigger pulse. 
In this mode, the exposure time of R, G, B and NIR channel can be adjusted independently. 

 

To use this mode: 
Set function 

 

Trigger   

 

 

 

TR=1 

 

Trigger origin, external 

 

 

TG=1 

 

Individual R, G, B and NIR exposure  

EI=0(individual) 
EI=1(tracking with G) 

 

Programmable exposure   

 

PER/PEG/PEB/PEIR=840 to 1194752 
(9.52 µs to 14.20 ms in 11.9 ns increments) 

 

Important note: 

 

If using individual exposure, the EEN signal represents the channel with the longest exposure time   

 

The minimum trigger interval   

Scan mode 

Trigger input via 

Minimum interval (

µ

s) 

Full/Binning 

Camera link 

54.8 

Hirose 12-pin 

59.3 

Sub-sampling/windowing 

Camera link 

30.4 

Hirose 12-pin 

34.9 

 
 

EEN

* Note

Exposure R

Exposure G

Exposure B

Exposure NIR

610clk

LVAL

16clk

2048clk

16clk

DVAL

Data

AP0

AP2047

Summary of Contents for LQ-401CL










































































Reviews:

No comments

Brands by name

Popular brands

Load more brands