I-CON COBALT
™
Manual Exposed Flush Valve
powered by ProLAST
®
Installation Instructions
VLV-FVL-MN3000 Series
• All plumbing should be installed according to applicable state
and local codes and regulations
• Before installation of the I-CON flushometer, ensure the water
closet or urinal fixture, drain line and water supply line are
properly installed
• Water supply lines must be sized to allow for appropriate
water flow for each fixture
• Flush all water supply lines of any debris before making and
connections
• Do not use pipe sealant or plumbing grease on any
components or couplings with exception to the control stop inlet
• A smooth jawed or strap wrench should be used for installation
to prevent damage to the finish of the I-CON flushometer and
components
The I-CON flushometer is designed to operate at water pressures
ranging from 15 to 100psi (103 to 689kPa). The fixture type
determines the minimum pressure required to the valve. Most
low consumption water closets are designed to operate with a
minimum flowing water pressure of 25psi (172kPa).
Flat Head Screwdriver
Smooth Jawed
Wrench
Pipe Solder
COBALT
™
MANUAL EXPOSED FLUSH VALVES
TOOLS NEEDED
PRIOR TO INSTALLATION
LIMITED WARRANTY
TOP EXPOSED
URINAL EXPOSED
REAR EXPOSED
page 1
Strap Wrench
I-CON Systems, Inc., for product support call 1-866-730-7192 or visit us online at support.i-con.com
Pipe Cutter
11 12 "
2 14 " MIN
FINISHED WALL
FINISHED FLOOR
4 34 "±
1
2 "
3/4" IPS
SUPPLY
14 18 "
2 14 " MIN
FINISHED WALL
FINISHED FLOOR
4 34 "±
1
2 "
1" IPS
SUPPLY
11 12 "
2 14 " MIN
FINISHED WALL
FINISHED FLOOR
4 34 "±
1
2 "
1" IPS
SUPPLY
11 12 "
2 14 " MIN
FINISHED WALL
FINISHED FLOOR
4 34 "±
1
2 "
3/4" IPS
SUPPLY
14 18 "
2 14 " MIN
FINISHED WALL
FINISHED FLOOR
4 34 "±
1
2 "
1" IPS
SUPPLY
11 12 "
2 14 " MIN
FINISHED WALL
FINISHED FLOOR
4 34 "±
1
2 "
1" IPS
SUPPLY
11 12 "
2 14 " MIN
FINISHED WALL
FINISHED FLOOR
4 34 "±
1
2 "
3/4" IPS
SUPPLY
14 18 "
2 14 " MIN
FINISHED WALL
FINISHED FLOOR
4 34 "±
1
2 "
1" IPS
SUPPLY
11 12 "
2 14 " MIN
FINISHED WALL
FINISHED FLOOR
4 34 "±
1
2 "
1" IPS
SUPPLY
Rev 022719
I-CON Systems, Inc. (I-CON) warrants that its commercial
manufactured products are made of first-class materials, are
free from defects, and are made to withstand normal use when
installed properly.Products have the following warranty periods:
3 years for COBALT™, COBALT Pro™, and COBALT Connect™
faucets and flush valves and I-CON EDGE® gateways. 1 year for
all other products and decorative finishes. The warranty period
begins on the date of purchase.
Products should be sent to I-CON at the customer’s expense.
I-CON will take a reasonable amount of time to determine if the
product is defective and whether it will be repaired or replaced.
During the warranty period, items will either be (1) repaired
at no charge using new replacement parts or (2) replaced
with either a new similar product or one manufactured from
new or serviceable used parts that is at minimum a functional
equivalent to the original. The course of action will be
determined at I-CON’s discretion. Replacement products that
are installed according to the instructions provided by I-CON will
assume the remaining warranty of the original product.
The limited warranty is only applicable to the product’s materials
and workmanship. No claims for labor, transportation, or other
incidental or consequential costs will be allowed. No extended
warranties are available. THE SOLE AND EXCLUSIVE REMEDY
FOR ANY DEFECTIVE PRODUCT IS LIMITED TO REPAIRING OR
REPLACING THE DEFECTIVE PRODUCT. Before installing and
using products, the purchaser is responsible to determine the
products’ suitability and assumes all risks and liabilities related
to the product.
This warranty only applies to persons and organizations that
purchase I-CON products directly from I-CON or an authorized
I-CON representative for the purpose of resale. This warranty
does not apply to the life of batteries or other consumables.
