background image

2

 

Rev. 08102020

 

 

At HydroHoist

®

, we take pride in bringing the most advanced, easiest to use, and lowest maintenance boat lift 

 

systems to the market. Installation of the lift is simple due to its design and ease of operation. 

 

The following pages contain step

-

by

-

step instructions of the installation and operation processes.

 

The Front Mount UltraLift

™ 

Series lift takes approximately 2 man

-

hours to assemble. Review all parts, hardware, 

and required tools before beginning assembly. Don

t forget: safety first. 

 

If you have questions, contact the Technical Support Team at 1

-

800

-

825

-

3379.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Legend:

 

Requires careful consideration

 

WARNING: could cause harm or damage to the lift, vessel, and user  

 

INTRODUCTION

 

Lifts must be installed by an approved HydroHoist

®

 installer. Failure to comply will result in termina-

tion of warranty and could cause injury to the user and damage to the lift and vessel. 

 

 

It is STRONGLY recommended that each installer read the manual before attempting an installation.  

 

Summary of Contents for Ultralift FM-6500LF






















Reviews: