manualshive.com logo in svg

Hydreka HYDRINS 2, Installation Manual, Page: 39 / 79

Share
Download
Hydreka HYDRINS 2 Installation Manual Download Page 39

 

 

HydrINS 2 / HydrINS 2 Mini flow meter  

User Manual  

 

Page 39 / 79 

8.5

 

Electrical power supply of Display A 

 

Risk of electrocution. Always disconnect the power supply before making any electrical 
connections. 

 

Potential damage to the device. The internal electronic components of the device can 
be damaged by static electricity, which might affect its performance characteristics and 
operation. 

 

Display A can be powered according to one of the following five modes: 

 

Internal 3.6 VDC lithium battery pack 

 

External 3.6 VDC lithium battery pack 

 

Internal 9 to 28 VDC alkaline battery pack 

 

An external 9 to 28 VDC power supply connected to the labelled 9-28 VDC terminals 

 

A 9 to 28 VDC external power supply connected to the military connector 

These different power supply modes can be implemented using the two elements illustrated below: 

 

Switch SW2 with two positions: 

Internal

 or 

External

 

 

Connector J15 

Summary of Contents for HYDRINS 2
















































































Reviews:

No comments