Hydreka HYDRINS 2 Installation Manual Download Page 22 | Manualshive

Page: 22 / 79

Hydreka HYDRINS 2 Installation Manual Download Page 22

HydrINS 2 / HydrINS 2 Mini flow meter

Installation Manual

Page 22 / 79

Figure 13: Valid positions of the HydrINS 2/HydrINS 2 Mini flow meter sensor for flow measurement

4.4

Typical installation of HydrINS 2 / HydrINS 2 Mini flow meters

Typical installations are as follows:



HydrINS 2: 1" insertion – drill 25 mm (0.98 inches) at least



HydrINS 2 Mini: two possibilities:

o

Either 1" insertion plus 1"-3/4" adapter – drill 25 mm (0.98 inches) minimum: this
can measure the inside diameter of pipes using diameter gauges marketed by
HYDREKA and adaptable to 1" tappings.

o

Or 3/4" insertion – drill 19 mm (0.75 inches) minimum: does not need an adapter.

The  preparation  of  an  insertion  point  compatible  with  HydrINS  2  or  HydrINS  2  Mini  is  exactly  the
same  as  for  the  preparation  of  a  classic  insertion  point  for  the  installation  of  a  connection.  No
additional  accessories  are  required.  After  drilling  the  pipe,  tighten  the  HydrINS  2  /HydrINS  2  Mini
probe to the ball valve.

Position at 1/8 diameter

Position at 1/2 diameter

«
...
20
21
22
23
24
...
»

Summary of Contents for HYDRINS 2
















































































Reviews:

No comments