HydraMaster CDS 4.6 Owner'S Manual Download Page 24 | Manualshive

Page: 24 / 126

HydraMaster CDS 4.6 Owner'S Manual Download Page 24

3-1: operating Instructions

3 - operating Instructions

This section of the manual contains the following instructions:

Before operating the CDS

CDS Start up

CDS flood Restoration Work

CDS Shut Down

3 Speed Throttle Control function

BEFORE OPERATINg THE CDS

locate the unit and equipment in a well-ventilated area.

1.

The CDS unit generates toxic fumes. Position the vehicle so that the fumes will be

directed away from the job site. Do not park where exhaust fumes can enter a building

through open doors, windows, air conditioning units or kitchen fans.

Check the fuel tank to be certain there is adequate fuel to complete the job.

2.

Position the wheel chocks on one of the front tires.

3.

If using a water supply hose which has not been used recently or if using a customer’s

4.

hose, first connect the hose to the faucet and flush out any debris which may be in
the hose. Afterwards connect the hose to the unit.
Check the chemical jug to see if you have enough concentrated chemical to finish

5.

the job. If not, mix and fill a 5 gallon chemical jug.
Connect all required hoses.

6.

When connecting the pressure hose to the pressure outlet connections at the front of

7.

the unit, go to the farthest area to be cleaned and connect to the cleaning tool. This
ensures that you have the proper length of hose required to perform the cleaning.

«
...
22
23
24
25
26
...
»

Summary of Contents for CDS 4.6































































































































Reviews:

No comments