manualshive.com logo in svg

HydraMaster CDS 4.6, Owner'S Manual, Page: 109 / 126

Share
Download
HydraMaster CDS 4.6 Owner'S Manual Download Page 109

9-1:  electrical System

9 - electrical System

Because the most difficult problem to trace in any system is often an electrical failure, 

HydraMaster has designed the CDS’ electrical system with the technician in mind.

This  section  of  the  manual  includes  CDS  wiring  schematics  and  diagrams  as  well  as 

troubleshooting guides.

The entire electrical system operates on 12 volts DC which is provided by the vehicle’s  

battery. 

To avoid equipment damage, it is very important to tie up any loose wires or hoses near 

the drive shaft area. Tie wraps are sufficient for wires and small hoses.  

When securing large hoses or wiring harnesses in the area of the drive shaft, tie down the 

components with a hose clamp, with a clear vinyl hose inserted onto the clamp.  on some 

installations, if the fuel injector wires are not properly secured, the wires could rub against 

the CDS drive shaft causing a short in the electrical system of the van.

Summary of Contents for CDS 4.6































































































































Reviews:

No comments