manualshive.com logo in svg

Hydac OF5 CM, Operating And Maintenance Instructions Manual

Share
Download
Hydac OF5 CM Operating And Maintenance Instructions Manual Download Page 64

7 | Performing maintenance

HYDAC FILTER SYSTEMS GMBH

64 / 80

BeWa OF5 CM 3580053c en-us print

7.3 Cleaning the protective screen

To protect the pump from coarse contaminant particles or for-
eign bodies, a protective screen is installed in the suction
lance. Clean the strainer regularly. Check the protective screen
immediately in the event of insufficient suction or delivery ac-
tion.

NOTICE

Operation without the protective screen

The filter unit will be damaged/destroyed

u

Always operate the filter unit with a protective screen.

Item

Description

1

Suction hose

2

Suction lance

3

O-ring

4

Protective screen

5

Protective pipe

6

Protective screen set consisting of:
- Protective screen
- O-ring
- protective pipe

Tab. 6: Suction lance with protective screen

To clean the protective screen, proceed as follows:

ü

Switch the filter unit off at the main switch.

ü

Wear gloves.

ü

Remove the pressure and suction lances from the con-
tainers/reservoirs.

ü

Empty the suction hose into a suitable container, dirt
tank etc.

1.

Rotate the protective pipe (5) away from the suction
lance (2) in counterclockwise direction.

2.

Remove the protective screen (4) from the protective
pipe.

1

2

3

4

5

6

7

8

9

Summary of Contents for OF5 CM

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands