HYDAC International FMMHP Operating And Maintenance Instructions Manual Download Page 24

Page: 24 / 28

FluidMonitoring Module High
Pressure

Technical Data

HYDAC Filter Systems GmbH

Page 24 / 28

BeWa FMMHP 3386918a en 2009-06-08.doc

2009-06-08

Technical Data

FMMHP Technical Data

Mounting position

vertical, with the direction of flow from bottom
to top.

Operating pressure, maximum

= without accumulator

15 ... 300 bar / 217 ... 3625 psi

with accumulator

15 ... 250 bar / 217 ... 4350 psi

Differential pressure

> 15 bar

Connectors (IN / OUT)

Test point type 1604 /
thread G¼ according ISO 228

Sealing material

FPM

Permissible viscosity range

1 ... 1000 mm²/s

Fluid temperature range

0° ... 85° C / 32° ... 185°F

Ambient temperature range

-30° ... 80° C / -22° ... 176°F

Storage temperature range

-40° ... 80° C / -40° ... 176°F

Weight

12.5 kg

For further technical details, please refer to the operating and maintenance manuals
of the respective component.

Customer Service

Shipping address for calibration and repair:

HYDAC Servicenter GmbH

Rehgrabenstrasse, Werk 7

66121 Saarbrücken – Dudweiler

Telephone:

++49 (0) 681 / 509 – 883

Telefax:

++49 (0) 681 509 324

E-Mail: [email protected]

Summary of Contents for FMMHP





























Search results

Summary of Contents for FMMHP

Reviews:

Related manuals for FMMHP

Brands by name

Popular brands

HYDAC International FMMHP, Operating And Maintenance Instructions Manual

Search results

Summary of Contents for FMMHP

Reviews:

Related manuals for FMMHP

Brands by name

Popular brands