background image

 

Technical details

 

CMP1000 

en(us) 

Page 39 / 44

MoWa CMP 3528418d en-us 2015-01-06.doc 

2015-01-06

 

Technical details 

General data 

 

Hydraulic fluid temperature 

0 … 70°C / 32 … 158°F 

ambient temperature 

0 … 50°C / 32 … 122°F 

Storage temperature 

-40°C … 80°C / -40°F … 176°F 

Relative humidity 

max. 90%, non-condensing 

Weight 

 

 

CMP1xx0-2  ~25 kg 

 

CMP1xx0-4  ~25 kg 

Hydraulic data 

 

Permissible suction pressure at 
suction port connection (IN) 

- 0.4 bar … 80 bar 

Pressure at return port connection 
(OUT) 

 

 

CMP1xx0-2  0.5 bar max. 

 

CMP1xx0-4  5 bar max. 

Pump type 

Gear pump 

Max suction height 

500 mm 

Sealing material 

NBR 

Suction port (IN) 

G ¼“ 

Return port connection (OUT) 

G ¼“ 

Permissible operating viscosity 
range 

CMP1xx0-2 

10 … 3000 mm²/s 

 

CMP1xx0-4 

10 … 1000 mm²/s 

Permissible viscosity range for the 
measurement operation 

CMP1xx0-2 

10 … 1000 mm²/s 

 

CMP1xx0-4 

10 … 800 mm²/s 

Total flow rate: 

50 Hz 

60 Hz 

CMP1xx0-2 

~ 180 ml/min 

~ 220 ml/min 

CMP1xx0-4 

~ 230 ml/min 

~ 260 ml/min 

 

Summary of Contents for CMP1 0-2 Series













































Reviews: