Hyd-Mech V-25APC Page 30 Manual Download

Page: 30 / 78

1.14

EARTH GROUNDING PROCEDURE

The customer is to provide and install a ground rod approx.. .60 (15mm) diameter, copper clad steel, to be driven

no less than 8’ (2.5m) into the ground, no more than 10’ (3m) away from control enclosure.

The ground rod is to be connected to customer’s in plant ground system. This connection shall be made directly

at the ground rod. (If applicable).

It is desirable that the overall resistance to ground measured at the ground rod does not exceed 3 ohms. Cus-

tomer is advised to consult local power company for further information on grounding.

The ground rod is to be connected to the ground terminal in the control enclosure using insulated, stranded 8

gauge copper wire.

An additional point to check is to ensure continuity of all ground within the control enclosure. Start with the main

power entrance ground terminal where the internal ground conductors should originate and then connect to, the

DIN terminal strip, control transformer, and the lid of control enclosure. Also, the PLC and Interface units should

have their own ground conductors connected to one of the main ground terminals.

A properly functioning ground system will:

provide safety for personnel.

ensure correct operation of electrical/electronic apparatus.

prevent damage to electrical/electronic apparatus.

help dissipate lightning strikes.

divert stray radio frequency (RF) energy from electronic/control equipment.

Summary of Contents for V-25APC















































































Search results

Summary of Contents for V-25APC

Reviews:

Related manuals for V-25APC

Brands by name

Popular brands

Hyd-Mech V-25APC, Manual

Search results

Summary of Contents for V-25APC

Reviews:

Related manuals for V-25APC

Brands by name

Popular brands