background image

1

FP3500-T11/FP3600-T11 

Installation Guide

„

FP unit (1) 

„

 Installation Guide (1) (this manual)

„

 Warning/Caution Information (1)

„

 Installation Gasket (1)(attached to the FP unit)

„

 Installation Brackets (4/set, 1set)

„

 USB Cable Clamp(2)

This unit has been carefully packed, with special attention to quality. However, should 
you find anything damaged or missing, please contact your local FP distributor 
immediately.

An FP-3500T/3600T series unit needs the following software for operation. As FP user 
manual, provided by PDF media, describes its details, download the manual below and 
get the further information. Visit our website below and get both software and reference 
manual. (URL:http://www.pro-face.com/otasuke/)
• Software

: Mouse Emulation Software

• Manual

: FP-3500T/3600T/3650T series User Manual

Caution

Be sure to read the “Warning/Caution Information” on the attached sheet before using 
the product.

Package Contents

Required software/Reference manual

D I S T R I B U T E U R   C O N S E I L   D E P U I S   1 9 8 5

System

Email :

  2 rue René Laennec 51500 Taissy France

 

 

Fax: 03 26 85 19 08,  Tel : 03 26 82 49 29

[email protected]

Site web : www.hvssystem.com

 

 

Distribué par :

Summary of Contents for FP3500-T11

















Reviews: