1. SONY Effio-E2 DSP adopted
2. Adopted 2-DNR technology, It reduces noise efficiently
in low light condition.
3. ATR(Adaptive Tone Reproduction)
4. True Day & Night function
5. Super Supreme Resolution(700 TVL - Color)
6. Multi function : High Light Mask, Motion Detection,
Privacy Mask, Defect Pixel Correction, Mirror
9. You can connect power supply regardless polarity.
1. Do not install the camera outdoors.
Use weather-proof housing for outdoor.
2. Choose an ideal location for the camera, since the
camera unit must be protected against moisture and
vibration.
3. Be careful not to scratch the camera unit, especially
lens glass.
4. Use the camera under proper temperature.
(-10℃ ~ +50℃)
5. Handle with care. Dropping it can cause serious
damage to the camera.
6. Avoid any direct sun light into the lens.
7. Use the adaptor regulated 12V DC, 500mA.
Dual voltage product can use 24V AC, 500mA adaptor.
(Option)
1. Remove the protective rubber before installing a CS
mount lens.(If you use a C mount lens, add a C mount
ring. - option)
2. Connect the video output jack to the monitor video in jack.
3. Connect power supply. Check the voltage.
7. This camera can distinguish daytime and night. And it
changes its mode according to intensity of illumination.
It can watch an object at most suitable mode, "Color
in daytime, and B/W at night".
8. Multi-language full OSD support
1. Manual iris lens
3. Back focus control
1) Before mounting a lens, please check whether it is
a C mount or CS mount lens.
2) CS mount lens : After removing the protective
rubber, attach the lens.
3) C mount lens : Before installing the lens, attach the
C mount ring to the camera.
4) Set the LENS mode to "manual" by OSD.
1) Attach a DC lens as like the manual lens connection.
2) Connect the lens plug to the auto iris lens connector
on the rear panel of the camera.
3) Set the LENS mode to DC and adjust DC level by
OSD.
2. Auto iris lens
Set focus of camera using 'back focus control lever'
of camera side after combining a lens.
700TVL
SUPER SUPREME RESOLUTION
CAMERA
SK-B300(D)/M445
MANUAL
FEATURES
CAUTION AND WARNING
DESCRIPTION OF OPERATION
LENS CONNECTION
(option)
DIMENSION
OVERVIEW
ACCESSORIES
If the product is to be put out of operation definitively,
take it to a local recycling plant for a disposal which
is not harmful to the environment.
Before calling service, check the following points for
possible misuse.
If you can't correct the problem after going through this
chart, contact a service professional for further assistance.
TROUBLESHOOTING GUIDE
Problem
Check point
Too dark or bright
picture
No Power
Poor picture quality
Shrinking picture
Readjust the contrast or brightness
controls on the monitor.
Clean the camera lens.
Readjust lens focus.
Check the condition of the power
sources.
Check for power connection
.
BACK FOCUS CONTROL
DC-TYPE
①DAMP COIL -
②DAMP COIL +
③DRIVE COIL +
④DRIVE COIL -
Auto Iris Lens Connector
④
③
②
①
BACK FOCUS CONTROL
C-MOUNT RING(option)
C MOUNT RING - (option)
①Menu setup buttons :
ㆍ
ㆍ
ㆍ
Video output :
③Input/Output terminal :
1. GND :
2. D/N IN :
3. MD OUT :
4. RS-485A :
5. RS-485B :
④Power input terminal :
ENTER : Used to access the menu and confirm
selection.
Up, Down : Used to move the cursor to up or
down.
Left, Right : Used to move the cursor to left or
right and change the value.
Used to connect the video monitor.
GROUND terminal
Switch to Day & Night Mode by
connecting an external signal to this port
(Using an 'EXT 1' or 'EXT 2' mode in Day&Night
menu)
Not available
Connect the control unit via a twisted,
2-conductor line to the port. RS-485A(+)
Connect the control unit via a twisted,
2-conductor line to the port. RS-485B(-)
You can connect 12V DC
regardless polarity.(Dual power product can
use 24V AC)
②
①
②
③
④
VIDEO
U
L
R
D
E
1 2 3 4 5
AC24V~
DC12V
1/4"-20UNC(20THREAD)
L : 4.5mm±0.2mm
(ISO standard)
VIDEO
U
L
R
D
E
1 2 3 4 5
AC24V~
DC12V
59.8
109.4
43.4
59.4
