8
CHANGES AND T YPING ERRORS RESERVED
CHANGES AND T YPING ERRORS RESERVED
CHANGES AND T YPING ERRORS RESERVED
7.2 T
apping
These machines have a special unit for tapping, it is a quick change device. During tapping, if you want the spindle
to reverse and to withdraw the tapping tip, just push up the grip handle (as shown in figure 7). If you want to
continue tapping, just press down the grip handle (as shown in figure 8).
Always keep the protective drill head cover closed during operation. It is controlled by a micro switch, ensuring that
the machine is switched off when the cover is opened.
7.3 W
ork
Table
aDjUsTmenT
•
Loosen the clamp handle on the left hand side (figure 9).
•
Turn the table handle until the table has reached its proper position (figure 10).
•
Tighten the clamp handle.
7.4 V
ise
aDjUsTmenT
(hU 32
only
)
Loosen the work table and vise set screws and turn the work table 180 degree, as shown in figures 11 and 12.
Retighten the set screws.
1.
Adjustment of feeding limit
To prevent unwanted penetration to work piece, the feeding limit
shall be set by adjusting the appropriate position of feeding depth
fixing button as long as the distance between the end of tool and
top surface if work piece is measured.
A. Setting of feeding depth
1. Loosen knob A.
2. Turn scaled ring B to desired feeding depth.
3. Lock knob A.
2.
Work table and vise adjustment
Loose the work table and vise set screw then turn the work table 180 degree, let the vise be upside.
Then completely tight the set bolt.
Figure 13.14.15.16
6.Please open water outlet valve and adjust a proper water outlet volume after power supplying.
Fig 17
11
Figure 13
Figure 14
Figure 15
Figure 16
Figure 17
Loose
Loose
Lock
Wrench Size 19m
Figure 11
Figure 12
Figure 13
shownin
Figure 12.
) If you want to continue to operate, just press down grip handle.(as
shownin
Figure 13.
)
3.
Protect safety guard shall be allocated in a proper position in operation. It is controlled by a micro
witch.(For CE)
10
4. Adjustment of feeding limit
To prevent unwanted penetration to work piece, the feeding limit
shall be set by adjusting the appropriate position of feeding depth
fixing button as long as the distance between the end of tool and
top surface if work piece is measured.
A. Setting of feeding depthFeed Depth Adjustment
5.Work table and vise adjustment
Loose the work table and vise set screw then turn the work table 180 degree, let the vise be upside.
Then completely tight the set bolt.
Figure 14.15.16.17
Figure 12
Figure 13
Lock
Loose
A
Figure 7
Figure 8
6.Please open water outlet valve and adjust a proper water outlet volume after power supplying.
Fig 18
11
7.Adjust work table position
(1)Firstly, loose the clamp handle in left hand
(Figure 19)
(2)Then swing the table handle to properly position.
(Figure 20)
(3)Finally tight the clamp handle.
(Figure 19)
8.Pulley Cover Open and Close Method
(1)Open iron cover
—
hold the handle of left iron cover (Figure 21A) and push upward to the highest point and then release
slightly; use locator (Figure 22 B) to fix the iron cover as open state.
Figure 14
Figure 15
Figure 16
Figure 17
Figure 18
Loose
Loose
Lock
Figure 19
Figure 20
6.Please open water outlet valve and adjust a proper water outlet volume after power supplying.
Fig 18
11
7.Adjust work table position
(1)Firstly, loose the clamp handle in left hand
(Figure 19)
(2)Then swing the table handle to properly position.
(Figure 20)
(3)Finally tight the clamp handle.
(Figure 19)
8.Pulley Cover Open and Close Method
(1)Open iron cover
—
hold the handle of left iron cover (Figure 21A) and push upward to the highest point and then release
slightly; use locator (Figure 22 B) to fix the iron cover as open state.
Figure 14
Figure 15
Figure 16
Figure 17
Figure 18
Loose
Loose
Lock
Figure 19
Figure 20
Figure 9
Figure 10
