Huvema HU 250 CS, Manual, Page: 4 / 20

4
CHANGES AND T YPING ERRORS RESERVED CHANGES AND T YPING ERRORS RESERVED CHANGES AND T YPING ERRORS RESERVED
a
ddiTional safeTy rules
Always keep in mind that:
• the machine must be switched off and disconnected from the power supply during maintenance and repairs,
• clamped workpieces may only be measured when the machine is switched off.
Never lean over the machine, mind loose clothing, ties, jewellery etc. and wear a cap.
Do not remove safety devices or guards. Never use the machine while a guard is open.
Always use safety glasses for machining rough materials.
Burrs and chips should only be removed using a sweeper or other aid, never with your bare hands!
Never leave the machine running unattended.
Always wear safety glasses!
2. T
ecHnical daTa
2.1 T
He
Hu 250cs
speed comprises as follows
:
High speed > sawing speed pos. 1: 40 m/min
Low speed > sawing speed pos. 2: 80 m/min
2.2 s
urvey and skeTcH of dimensions
See figure 2.01
Height : 1750 mm
Width : 555 mm
Depth : 830 mm
Weight : 175 kg
3. d
escripTion of macHine
The machine is standard equipped with a machine base with incorporated
cutting oil tank and pump.
The machine is fitted with a tolerance-free long-life worm and worm wheel. The worm gear runs in an oil bath case and
is virtually maintenance-free.
The machine is fitted with a double, self-centring material vice.
The machine can mitre, slot and cut recessed corners in both directions. For this last form of operation it is of special
importance that the saw unit as a whole can turn around its axis.
The machine can saw various profiles in various dimensions and cross -sections.
A survey of these can be found in chapter 5.3 “Sawing capacity”.
The protective guard opens and closes automatically. The saw blade can easily be exchanged. The machine as standard
is equipped with an adapter for the saw blade (see technical data). If ordered a different adapter can be supp lied.
4. i
nsTallaTion
4.1 i
nsTallaTion and mounTinG
Unpack the machine.
• Determine where the sawing machine will be placed. In doing so take into account the feed and discharge of
materials, optional built-on accessories, maintenance and repairs.
• Remove the plastic plug from the saw head (fig. 4.01 B). If so required a lifting hook M20 DIN 580 can be screwed
into the hole.
• Place the saw unit - if necessary by means of hoisting equipment – on the machine base (cover at the rear) and
attach each other.
• Secure the machine to the floor. The necessary holes have already been made in the machine base.
• Install the handle in the saw head and lock it (fig 4.01A).
• Install the 3 short handles in the boss of the machine vice.
• Install the stretcher in the clamp.
• Slide the plastic tube coming from the cooling pump onto the tap which is positioned on top of the protective
guard of the saw unit (fig 4.02A).
• Check on the level gauge of the saw head whether it contains sufficient oil. If necessary fill up (fig. 4.01, see arrow).
• Install the cover at the rear of the machine base.
• Install the saw blade (see chapter 5.4).
3
exceeded all claims relating to the faults concerned will expire. Claims about faults which are not
externally noticeable are to put in as soon as po ssible, however, not later than two weeks after
expiry of the period of guarantee. If this period is exceeded all claims relating to the faults
concerned will expire. The purchaser’s appeal for guarantee does not relinquish his contractual
obligations towards us. As long as the purchaser does not fulfil his contractual obligations
towards us we deny our obligation to render guarantee.
2 Technical data
2.1
The HU 250CS speed comprises as follows:
High speed > sawing speed pos. 1: 40 m/min
Low speed> sawing speed pos. 2: 80 m/min
2.2 Survey and sketch of dimensions (see fig. 2.01)
Dimensions and weight of the machine
HU 250CS
Height : 1750 mm
breadth : 555 mm
Depth : 830 mm
Weight : 175 kg
Fig. 2.01
3. Description of machine
The machine is standardly equipped with a machine base with incorporated cutting
oil tank and pump.
The machine is fitted with a tolerance-free long-life worm and worm wheel. The
worm gear runs in an oil bath case and is virtually maintenance -free.
The machine is fitted with a double, self-centring material vice.
The machine can mitre, slot and cut recessed corne rs in both directions. For this last
form of operation it is of special importance that the saw unit as a whole can turn
around its axis.
The machine can saw various profiles in various dimensions and cross -sections.
A survey of these can be found in cha pter 5.3 “Sawing capacity”.
HU 250CS
Fig. 2.01