HUSTLER Super 104 Operator'S Manual Download Page 12

M

AX

  O

F  1

0%  ETHANO

L  

IN

  F

U

EL

IG

H

ER

  T

HA

 E1

0  F

UEL

  V

OIDS

  W

AR

RA

N

TY

H

     If you lose steering control while operating the machine, place the steering
control levers in the park brake position immediately. 

Inspect the machine and

involve your dealer to resolve the problem before continuing to operate.

     If pump belt fails, steering control will be lost. 

Refer to owner’s manual for

inspection and replacement intervals and refer to above paragraph for
emergency procedures.

600899

REV B

2-6

606835

of spillage and avoid creating any source of 
ignition until gasoline vapors have dissipated.

Keep gasoline away from open flame or spark and 
store machine away from open flame or spark or 
pilot light such as on a water heater or 
appliances.

Refuel outdoors. Never refuel or drain the 
gasoline from the machine indoors.

Never attempt to start the engine when there is a 
strong odor of gasoline fumes present. Locate 
and correct the cause.

Store gasoline in an approved container and keep 
it out of the reach of children. Never buy more 
than a 30-day supply of gasoline.

Do not fill fuel containers inside a vehicle or on a 
truck or trailer bed with interior carpets or plastic 
truck bed liners. Always place gasoline
containers on the ground away from your vehicle 
before filling.

When practical, remove the machine from the 
truck or trailer and refuel the machine with its 
wheels on the ground. If this is not possible, then 
refuel such machine on the truck or trailer using a 
portable container and not a fuel dispenser 
nozzle. If a fuel dispenser nozzle must be used, 
keep the nozzle in contact with the rim of the fuel 
tank or container opening at all times until 
fueling is complete. Do not use a nozzle lock-
open device.

Never use gasoline for cleaning parts.

Read and observe safety precautions elsewhere 
in this manual.

Gasoline is harmful or fatal if swallowed.

Avoid prolonged breathing of vapors.

Long-term exposure to vapors can cause serious 
injury and illness.

Keep gasoline away from eyes and skin.

Keep face away from nozzle and fuel tank or fuel 
container opening.

If gasoline is spilled on clothing, change clothing 
immediately.

Safety and Instructions Decals

The decals are designed to give the operator and mechanic 

brief daily operational and service information. Use these 
decals as an extension of this manual. Do not remove or 
obliterate the decals. Replace unreadable or missing decals.

It is the 

owner’s responsibility

 to make certain that the 

operators and mechanics read and understand all decals 
before operating this machine. 

 

The following illustrations show the safety decals that are 

located on the mower. A brief explanation is shown to help 
the operator understand the decal’s meaning.

Specific safety warning decals are located on the 
equipment near the immediate areas of potential 
hazards. Do not remove or obliterate these decals. 
Replace them if they become non-readable.

Read Operator’s Manual and Safety Warning Decals before 
attempting to operate this machine.

Do not smoke while refueling.

Do not remove the fuel tank cap or fill tank with engine running or 
while the engine is hot.

Allow engine to cool before storing machine inside a building.

Store away from open flame or spark if there is fuel in tank.

Clean up any gasoline spills.

Do not refuel while in enclosed trailer or other enclosed areas.

Maximum of 10% ethanol (E10) in fuel. Fuels with greater than 10% 
ethanol, (such as E15, E20 and E85) voids warranty. Fuels with 

greater than 10% ethanol are not approved for use and such illegal 

use could cause equipment failure and pose a fire hazard.

Part Number 602041

WARNING:

Hot surface!

Keep a safe distance from the machine.

Part Number 600899      

  

If you lose steering control while operating the machine, place the 
steering control levers in the park brake position immediately. 

Inspect the machine and involve your dealer to resolve the problem 

before continuing to operate.

If pump belt fails, steering control will be lost. Refer to owner’s 
manual for inspection and replacement intervals and refer to above 

paragraph for emergency procedures.

WAR

N

ING

602041

Summary of Contents for Super 104





























































Reviews: