manualshive.com logo in svg

Husqvarna TE 250, Owner'S Manual

Share
Download
Husqvarna TE 250 Owner'S Manual Download Page 20

6 CONTROLS

18

6.9

Turn signal switch (All EU/AR standard models)

S04822-10

Turn signal switch

1

is fitted on the left side of the handlebar.

Possible states

Turn signal off

–

The turn signal switch is in the cen-

tral position.
Left turn signal, on

–

The turn signal switch is turned

to the left.
Right turn signal, on

–

The turn signal switch is

turned to the right.

6.10

Emergency OFF switch (All EU/AR/CN standard models)

S04823-10

The emergency OFF switch

1

is fitted on the right side of the

handlebar.

Possible states

Ignition off

–

In this position, the ignition circuit

is interrupted, a running engine stops, and a

non-running engine will not start.
Ignition on

–

In this position, the ignition circuit is

closed and the engine can be started.

6.11

Start button (All US standard models)

H03656-10

Start button

1

is fitted on the right side of the handlebar.

Possible states

• The start button

is in the basic position

• The start button

is pressed

–

In this position, the starter

motor is actuated.

6.12

Start button (All EU/AR/CN standard models)

S04823-11

Start button

1

is fitted on the right side of the handlebar.

Possible states

• The start button

is in the basic position

• The start button

is pressed

–

In this position, the starter

motor is actuated.

Summary of Contents for TE 250










































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands