Husqvarna TC 50 2023 Owner'S Manual Download | Manualshive

Page: 8 / 196

background image

2 SAFETY ADVICE

6

2.1

Use definition

–

intended use

This vehicle has been designed and built to withstand the normal stresses and strains of racing. This vehicle

complies with the currently valid regulations and categories of the top international motorsports organizations.

Info

Only operate this vehicle in closed-off areas remote from public road traffic.

2.2

Misuse

The vehicle must only be used as intended.
Dangers can arise for people, property and the environment through use not as intended.
Any use of the vehicle beyond the intended and defined use constitutes misuse.
Misuse also includes the use of operating and auxiliary fluids which do not meet the required specification for

the respective use.

2.3

Safety advice

A number of safety instructions need to be followed to operate the product described safely. Therefore read

this instruction and all further instructions included carefully. The safety instructions are highlighted in the text

and are referred to at the relevant passages.

Info

Various information and warning labels are attached in prominent locations on the product described.

Do not remove any information or warning labels. If they are missing, you or others may not recognize

dangers and may therefore be injured.

2.4

Degrees of risk and symbols

Danger

Identifies a danger that will immediately and invariably lead to fatal or serious permanent injury if the

appropriate measures are not taken.

Warning

Identifies a danger that is likely to lead to fatal or serious injury if the appropriate measures are not

taken.

Caution

Identifies a danger that may lead to minor injuries if the appropriate measures are not taken.

Note

Identifies a danger that will lead to considerable machine and material damage if the appropriate measures are

not taken.

Note

Indicates a danger that will lead to environmental damage if the appropriate measures are not taken.

«
...
6
7
8
9
10
...
»

Summary of Contents for TC 50 2023





































































































































































































Reviews:

No comments

Related manuals for TC 50 2023

Brand: Free Spirits Pages: 32

Brand: LAZER Pages: 19

Brand: yasuni Pages: 8

Brand: ICON Vehicle Dynamics Pages: 4

Brand: DYNATEK Pages: 3

Brand: DYNATEK Pages: 8

YZF-R1P 2001-2003

Brand: Yamaha Pages: 26

Brand: Yamaha Pages: 36

Brand: Yamaha Pages: 47

Brand: Yamaha Pages: 87

Brand: Yamaha Pages: 106

Brand: Yamaha Pages: 114

Brand: Yamaha Pages: 78

Brand: Yamaha Pages: 120

Brand: Yamaha Pages: 82

Brand: Yamaha Pages: 132

Brand: Yamaha Pages: 122

Brand: Yamaha Pages: 124

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands