Husqvarna TC 50 2023 Owner'S Manual Download

Page: 20 / 196

6 CONTROLS

Possible states

• Choke function activated

–

The choke lever is pushed up all

the way to the stop.

• Choke function deactivated

–

The choke lever is pushed

down all the way to the stop.

6.11

Kick starter lever

H01184-10

Kick starter lever

is fitted on the right side of the engine.

The kick starter lever can be swiveled.

Info

Before riding, swing the kick starter lever inwards towards

the engine.

6.12

Foot brake lever

401956-10

Foot brake lever

is located in front of the right footrest.

The rear brake is engaged with the foot brake lever.

6.13

Plug-in stand

402581-10

The fixture for plug-in stand

is located on the frame on the

left side of the vehicle.
The plug-in stand is used to park the motorcycle.

Info

Remove the plug-in stand before riding.

Summary of Contents for TC 50 2023





































































































































































































Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands

Husqvarna TC 50 2023, Owner'S Manual

Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands