Husqvarna LH 700 Page 26 Operator'S Manual Download

Page: 26 / 36

Technical data

LH 700

LH 804

Operation weight (EN500, incl. oil, ½ fuel), kg/lb

779/1717

820/1808

Engine brand, type

Hatz, 1 D90V

Engine power, kW/hp @rpm

11.5/15.4 @3000

Vibration frequency, Hz/rpm

56/3000

Amplitude, mm/in.

2.5/0.098

Centrifugal force, kN/lbf

95/21375

Operation speed, m/min or ft./min

30 or 98.4

Max. tilt, degrees/%

20/35

Fuel tank capacity, l/qts

7.0/7.40

Engine oil capacity *, l/qts

1.9/2.0

Hydraulic oil tank capacity, l/qts

27.0/7.1

Eccentric element, l/qts

1.0/1.1

Engine oil *

Shell Rimula R4 L 15W-40 Shell Rimula R4 L 15W-40

Eccentric element oil

Shell Rimula R4 L 15W-40 Shell Rimula R4 L 15W-40

Hydraulic oil

Shell Tellus S3 V68

Biological hydraulic oil (optional)

Shell Naturelle HF-E46

Fuel *

Ultra-low-sulfur diesel fuel

only

Ultra-low-sulfur diesel fuel

only

Fuel consumption, l/h or qts/h

2.3 or 2.4

Battery voltage, V/Ah

12/44

12/48

* = For further information and questions about this

specific engine, refer to the engine manual or the web

site of the engine manufacturer.

Noise and vibration emissions

LH 700

LH 804

Sound power level, measured dB (A)

108

106

As specified by the engine manufacturer. The power rating of the engine indicated is the average net output

(at specified rpm) of a typical production engine for the engine model measured to SAE standard J1349/

ISO1585. Mass production engines may differ from this value. Actual power output for the engine installed on

the final product will depend on the operating speed, environmental conditions and other values.

1177 - 001 - 02.04.2020

Summary of Contents for LH 700





































Search results

Summary of Contents for LH 700

Reviews:

Related manuals for LH 700

Brands by name

Popular brands

Husqvarna LH 700, Operator'S Manual

Search results

Summary of Contents for LH 700

Reviews:

Related manuals for LH 700

Brands by name

Popular brands