4. Lift the earmuffs out and up until they lock in standby
position. (Fig. 8)
5. Do a mark on the cable.
a) For helmets H300, H200 and JSPMK2 EVO, do
a mark 27 cm/11 in (X) from each earmuff.
b) For helmet Petzl Alveo, do a mark 14.5 cm/6 in
(Y) from each earmuff. (Fig. 9)
6. Put the helmet attachment in the slot on the helmet.
(Fig. 10)
7. Continue to assembly instructions for your approved
helmet.
CAUTION: Make sure that the cable is not
twisted or has a small bend radius. Make
sure that the cable can move smoothly into
the opening of the helmet.
To assemble the earmuffs to the helmet H300
1. Release the head harness from the helmet. (Fig. 11)
2. Attach the cable to the holes with the cable ties. (Fig.
12)
3. Cut the cable tie and push the cable tie lock into the
side slot.
4. Make a loop of the cable and attach the head
harness and neck protection. Make sure that the
cable is between the helmet shell and the head
harness. (Fig. 13)
To assemble the earmuffs to the helmet H200
1. Release the head harness from the helmet. (Fig. 14)
2. Make a loop of the cable and attach the cable to the
head harness with the cable ties. (Fig. 15)
3. Cut the cable tie.
4. Attach the head harness. Make sure that the cable is
between the helmet shell and the head harness.
(Fig. 16)
To assemble the earmuffs to the helmet
JSPMK2 EVO
1. Release the head harness from the helmet. (Fig. 17)
2. Make a loop of the cable.
3. Attach the cable to the head harness with the cable
ties. Use a hole that is not used. (Fig. 18)
4. Cut the cable tie.
5. Put the cable in the rear part of the helmet.
To assemble the earmuffs to the helmet Petzl
Alveo
1. Put the cable in a loop rearward. (Fig. 19)
2. Attach the cable to the head harness with cable ties.
Attach the cable tie through the backstrap of the
headband. (Fig. 20)
3. Cut the cable tie.
4. Put the remaining part of the cable in a loop forward,
in front of the forehead headband.
5. Remove the sealing ring on one of the earmuffs. Put
the cable through the headband and put the cable in
the correct position.
6. Attach the cable behind the plastic clips on the inner
side of the helmet. (Fig. 21)
To put the earmuffs in operation position
1. Put the helmet on your head.
2. Adjust the earmuffs until they are tight around your
ears and tight against your head. (Fig. 22)
To put the earmuffs in standby position
• Lift the earmuffs out and up until they lock in standby
position. (Fig. 23)
To put the earmuffs in parking position
1. Put the earmuffs in standby position.
2. Turn the earmuffs rearward along the side of the
helmet until they lock in the parking position. (Fig.
24)
To assemble the boom microphone
Use a boom microphone in environments with much
noise. A boom microphone decreases the noise during
phone calls and two-way radio calls.
Note: A boom microphone is not supplied with the
product but is available as an accessory. Refer to
www.husqvarna.com for more information.
1. Make sure that the product is off.
2. Connect the boom microphone to the microphone
input on the right earmuff. (Fig. 25)
Operation
Introduction
WARNING: Before you operate the product,
you must read and understand the safety
chapter.
To charge the product
Note: The product is not supplied with a charger but you
can purchase a separate charger. You can also
purchase a replacement charger cable as an original
spare part. The Husqvarna part number: 594 95 63-01.
Refer to www.husqvarna.com for more information.
8
579 - 005 - 05.07.2019
Summary of Contents for HP310-1
Page 3: ...7 8 9 X Y 10 11 12 13 14 ...
Page 4: ...15 16 17 18 19 20 21 22 ...
Page 5: ...23 24 25 26 27 ...
