Husqvarna FE 450 Owner'S Manual Download Page 55

Page: 55 / 128

12 SERVICE WORK ON THE CHASSIS

F00458-10

–

Disconnect plug-in connector



F00459-10

–

Remove screws



–

Pull off foot brake cylinder from the push rod.

F00294-01

–

Remove the connecting link of the chain.

–

Take off the chain.

F00460-10

–

Remove nut



and pull out the swingarm pivot.

–

Push the swingarm back and secure it against falling over.

F00461-10

–

Hold the shock absorber and remove screw



–

Remove the shock absorber carefully at the bottom.

12.17

Installing the shock absorber

F00462-10

Main work

–

Carefully position the shock absorber into the vehicle from the bottom.

–

Mount and tighten screw



Guideline

Screw, top shock

absorber

M10

60 Nm

(44.3 lbf ft)

Loctite

2701™

Summary of Contents for FE 450

































































































































Search results

Summary of Contents for FE 450

Reviews:

Related manuals for FE 450

Brands by name

Popular brands

Husqvarna FE 450, Owner'S Manual

Search results

Summary of Contents for FE 450

Reviews:

Related manuals for FE 450

Brands by name

Popular brands