Husqvarna FE 450 Owner'S Manual Download Page 29

Page: 29 / 128

PREPARING FOR USE

–

Rides at high temperature and slow speed. (

p. 29)

–

Rides at low temperature or in snow. (

p. 29)

8.5

Preparing for rides on dry sand

102136-01

–

Fit a dust cover on the air filter.

Dust cover for air filter (79006920000)

Info

See the

Husqvarna Motorcycles

accessories fitting instructions.

102138-01

–

Fit a sand cover on the air filter.

Sand cover for air filter (79006922000)

Info

See the

Husqvarna Motorcycles

accessories fitting instructions.

600868-01

–

Clean the chain.

–

Fit the steel sprocket.

Tip

Do not grease the chain.

–

Clean the radiator fins.

–

Straighten bent radiator fins carefully.

M01459-01

(All 450 models)

–

Change the clutch spring.

Clutch spring, hard (78932005000)

8.6

Preparing for rides on wet sand

102137-01

–

Fit a waterproofing device on the air filter.

Waterproofing device for air filter (79006921000)

Info

See the

Husqvarna Motorcycles

accessories fitting instructions.

Summary of Contents for FE 450

































































































































Search results

Summary of Contents for FE 450

Reviews:

Related manuals for FE 450

Brands by name

Popular brands

Husqvarna FE 450, Owner'S Manual

Search results

Summary of Contents for FE 450

Reviews:

Related manuals for FE 450

Brands by name

Popular brands